Models > FAV6800AWQ

FAV6800AWQ Maytag Washer - Overview

Get Parts and Repair Help for FAV6800AWQ

If you know the washer repair part you need, you can browse the list of all parts on the FAV6800AWQ, or you can search by name or part description. You can also find your part by where it is located on the FAV6800AWQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FAV6800AWQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$108.82

Drain Pump - 120V 60Hz

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$5.40

Hose Clamp

This hose clamp is sold individually.

$8.05

Leveling Leg and Pad

This part includes locknut.

$2.70

SCREW

Sold Individually.

$9.56

INLET HOSE

This hose can handle hot or cold water and is five feet long.

$5.86

Hinge Bushing

$4.19

Inlet Hose Gasket

This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.

$5.30

Single Washer Inlet Strainer

Found at the end of the inlet hoses.

$5.17

SCREW

This screw is sold individually.

$57.70

Water Inlet Valve with Thermistor

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

OLD PUMP STOPPED DRAINING THE MACHINE- IMPELLER IN PUMP WORE OUT

  • Customer: Deborah from Westfield MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 56 of 62 people found this instruction helpful
FIRST- I UNPLUGGED AND COMPLETELY DRAINED MACHINE OF WATER BY PUTTING HOSE AT GROUND LEVEL NEAR DRAIN .

SECOND- REMOVED BACK PLATE TO WASHER
SAVING ALL HARDWARE.

THIRD- DISCONNECTED IN AND OUT HOSE TO PUMP. TWISTED PUMP GENTLY AS TO POP IT OUT OF SLOTS IN BOTTOM OF MACHINE.

FOURTH- DISCONNECTED WIRES TO OLD PUMP HOOKED T... read more

Belt Broke

  • Customer: Nicole from Ottsville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 15 of 16 people found this instruction helpful
Luckily, I found someone else with the same story, and read that you need the clutch assembly and the belt at the same time. One night when we started the washer, it made a metal seizing type squeal. There was smoke everywhere. After opening the washer, the belt burned through but the clutch had also seized which was the cause. Replaced both. Needle bear... read more

Broken Pump

  • Customer: Drake from Crofton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old to new pump. Insta... read more