Quick Question!

Have you ever purchased from PartSelect.com before?

Models > F9857W0

F9857W0 Roper Range - Overview

Get Parts and Repair Help for F9857W0

If you know the range repair part you need, you can browse the list of all parts on the F9857W0, or you can search by name or part description. You can also find your part by where it is located on the F9857W0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.90

Surface Burner Plug-In Block Kit

This newer-style terminal block kit includes two metal brackets, two pre-crimped wires with terminals, two ceramic wire nuts, a heat shrinking tube, and a mounting screw.

$20.03

Wheel, Blower (Includes Illus.

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance.

$29.59

Temperature Sensor

This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.

$35.44

Burner Switch Kit

This push-to-start Robertshaw style replacement for load rated switches has a clockwise rotation. It also has a break off shaft, and comes with plastic adapters.

$28.74

Delta Frame Surface Unit - 6"

This 6 inch surface burner with reinforced delta frame carries 1250 watts and 240 volts. It has four turns and is compatible with many electric ranges. Its center medallion is all ...

$60.59

Burner Surface Element - 8"

Sold individually.

$66.28

Bake Element

This element has push-on terminals.

$21.66

SWTCH-LITE

DISCONTINUED

DISCONTINUED

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 127 of 164 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Bought motor, then bought blower wheel also

  • Customer: Daniel from Coatesville, PA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 65 of 77 people found this instruction helpful
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put ... read more

Burner would not heat

  • Customer: Edward from Malvern, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 23 of 30 people found this instruction helpful
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the right level. I got ... read more