F71C765BS0 Frigidaire Dishwasher - Instructions

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

First I noticed that the old gasket had disintergrated along the bottom. Next I removed the the gasket being careful to observe how it was installed. There are these notched areas of the gasket that belong in the lower corners. I think the notches are designed to help hold the gasket in place and make the gasket bend around the corner. The gasket made closing the door very hard at first but after one wash cycle the fit became much more comfortable. The heat probably made the gasket more pliable. Problem solved.

I started by dismantling my dishwasher from the top down, beginning with the water distributor propellor. Beneath that was a plastic filter that crumbled when you touched it, and basically came off in my hands. Eventually, I figured out that the motor could be removed when accessed from underneath, and once I got it out I just pulled everything apart. Some plastic parts only needed descaling, but others were essentially rotten. Both impellers were in particularly bad shape - their blades were broken off and their shafts were literally fused to the axle of the motor - I had to use a wood chisel & hammer to carve them off!

Putting everything back together was fairly straight forward - I wish some of the diagrams included with the parts were a little more detailed, but I found that if I paid close attention to the design of every part there was some logic to how they fit with one another. The only real problem I had was with the filter cover - this part had a needlessly complicated attachment design that required a special Frigidaire tool to snap into place that I did not have - ultimately I had to modify the part to get it to fit in place and then devise another means of securing it.

In the end, everything worked out fine - the dishwasher has never worked or sounded better!

*

A few days after I got the dishwasher working again, my garbage disposal jammed. Upon inspection, I determined that a blade from the lower impeller of my dishwasher was the culprit! Dispirited, I began the tedious process of taking apart the dishwasher again, expecting to find a shattered impeller that I must have somehow installed incorrectly. But when I got everything open, the lower impeller looked perfect! It must have been a blade from the old impeller that jammed my disposal. As a head's up, if your own dishwasher suffers a mechanical failure, be sure none of the parts wind up in your disposal.

Partselect.com was great to deal with, they emailed me information letting me know items were shipping with tracking numbers.
ordered on wed. received on Sat!
Springs were very easy, just put dishwasher on its side and hook to the holes in the botom of dishwasher!
The door gasket just slid into the grooves that were around the door.
Everything works great now!
Partselect.com was great to deal with

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

I ordered a new door gasket, wich is not very common for these type of dishwasher anymore, I installed it in less than 15 minutes. I turned the machine on fully loaded and the machine did not leak a single drop. It save me a bundle since I was considering buying a new dishwasher. THANK YOU!!

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

Very easy fix, it's the second time I ordered this perticulsr part and it once again prolonged the life of this dishwasher for just a few dollars. The door seal arrived in just a few very short days and was easily installed with no tools in less than 10 minutes. The web site made locating, ordering, and paying for the part needed extremely once again. Thanks

pulled the old gasket out, and pushed the new one into the slot where the old one came out. Very simple repair, and I'm a girl!!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Remove the old gasket simply by pulling it off. I installed the new gasket by starting in one corner and simply pushing the gasket firmly into the groove and working my way around. No tools required. My child could have done it. Problem solved. It takes two or three cycles for the gasket to "break in" and form precisely to the door. Leave the door locked a couple of days to hasten the "break in".

I used the scissors to open the bag the gasket came in. From there it was just seeing how the old, worn gasket was seated in the track around the inside of the dishwasher. Pulling the old one out and snapping the new one in the same way. When I was finished, there was about an inch between the two ends at the bottom where the gasket wasn't quite long enough for them to meet. I was a bit concerned seeing the basin fills with water. So I cut an inch off the best part of the old gasket to fill the space. No leaks! It works great and was so easy to do.

I read the instructions that others had posted and completed the repair in less than 5 minutes!

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!