Models > EV150NXKW1

EV150NXKW1 Whirlpool Freezer - Overview

Get Parts and Repair Help for EV150NXKW1

If you know the freezer repair part you need, you can browse the list of all parts on the EV150NXKW1, or you can search by name or part description. You can also find your part by where it is located on the EV150NXKW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your freezer. We’ve also included any installation videos we have for EV150NXKW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the EV150NXKW1 [Viewing 5 of 5]

$2.52

Light Bulb - 40W

Sold individually.

$17.62

Defrost Timer Kit

This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$5.54

Touch-Up Paint - White

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$42.63

Evaporator Fan Motor Kit

This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-on fan blade.

$24.55

Light Socket Kit

The bulb is sold separately.

$8.17

Spray Paint - 12 oz. - White

$2.70

SCREW

$62.13

Door Handle Kit of 2 - Black

Almond handle no longer available. NOTE: As per the manufacture the handle may have to be cut to fit.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 86 of 89 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

Unit very noisy and freezer too warm

  • Customer: Michael from Churchville NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 40 of 44 people found this instruction helpful
First I removed the racks in the freezer. The rack supports on the sides lift off without tools. The evaporator cover is at the back of the freezer. 4 phillips head screws. The cover lifts up then forward to expose the evaporator, evaporator fan and duct. The duct is held by 3 hex head screws. The evaporator fan is attached to the duct with a wiring pigtail ... read more

Freezer Iced up, dripping water into refrigerator below

  • Customer: Robert from Bradenton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 34 of 41 people found this instruction helpful
De-iced the refrigerator. Removed two screws from the thermostat panel on the upper refrigerator section. Tilted it down, removed two speed nuts holding the timer, unplugged the timer plug. Determined from the instruction sheet (easy to follow) what time delay function is used, based on wire colors, placed the jumper on the correct terminal on the new tim... read more