Quick Question!

Have you ever purchased from PartSelect.com before?

Models > EV150NXKW0

EV150NXKW0 Whirlpool Freezer - Overview

Get Parts and Repair Help for EV150NXKW0

If you know the freezer repair part you need, you can browse the list of all parts on the EV150NXKW0, or you can search by name or part description. You can also find your part by where it is located on the EV150NXKW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your freezer. We’ve also included any installation videos we have for EV150NXKW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the EV150NXKW0

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

Order within the next 11 hrs and your part ships today!
$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.

Order within the next 11 hrs and your part ships today!
$62.75

Evaporator Fan Motor Kit

The evaporator is found in the back of the freezer. This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-...

Order within the next 11 hrs and your part ships today!
$35.17

Light Socket Kit

The bulb is sold separately.

Order within the next 11 hrs and your part ships today!
$7.22

Touch-Up Paint - White

18ml

Order within the next 11 hrs and your part ships today!
$11.07

Spray Paint - 12 oz. - White

Order within the next 11 hrs and your part ships today!
$74.75

Door Handle Kit of 2 - Black

Almond and white handle no longer available. NOTE: As per the manufacture the handle may have to be cut to fit.

Order within the next 11 hrs and your part ships today!
$6.80

Touch-up Paint - Black

16ml

Order within the next 11 hrs and your part ships today!
$18.42

Leveling Leg

Sold individually.

Order within the next 11 hrs and your part ships today!
$67.62

Compressor Relay/Overload Kit

The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed. The overload provides extra protection for the compressor motor.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 121 of 129 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

Unit very noisy and freezer too warm

  • Customer: Michael from Churchville, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 63 of 67 people found this instruction helpful
First I removed the racks in the freezer. The rack supports on the sides lift off without tools. The evaporator cover is at the back of the freezer. 4 phillips head screws. The cover lifts up then forward to expose the evaporator, evaporator fan and duct. The duct is held by 3 hex head screws. The evaporator fan is attached to the duct with a wiring pigtail ... read more

Light Would Not Go On In The Refrigerator

  • Customer: DANIEL from MINNEAPOLIS, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 48 of 55 people found this instruction helpful
First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered... read more