Models > ESL25JFWDBS

ESL25JFWDBS General Electric Refrigerator - Overview

Get Parts and Repair Help for ESL25JFWDBS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ESL25JFWDBS, or you can search by name or part description. You can also find your part by where it is located on the ESL25JFWDBS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ESL25JFWDBS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$9.20

Temperature Sensor

Also known as Thermistor. This part is used to sense the temperature in the cabinet.

$29.00

Ice Bucket Auger

When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

$44.40

Dual Inlet Water Valve

This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

$18.07

Drawer Slide Rail - Right Side

$151.68

Main Electronic Control Board

This board controls the operation of the unit. Note: This part has been updated by the manufacturer. It may differ in appearance but will function the same as the original.

$61.43

Ice and Water Filter

Sold individually. NOTE: As per the manufacture this is an updated water filter. If you have never installed the updated filter or your old filter was made by Culligan, you may need the adapter to install the filter. GE Refrigerator Water Filter. If you have never installed this new style filter or your old filter was made by Culligan you may need the adapter to install it.

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$15.92

Drawer Slide Rail - Left Side

When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. Rail ONLY.

$4.21

Bearing Slide

Sold individually.

$31.30

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigertor water dispenser not working BUT ice machine is working

  • Customer: ralph from bristow VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 536 of 584 people found this instruction helpful
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and pr... read more

Plastic Auger blades broke in ice tray

  • Customer: Tim from Newport News VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 301 of 306 people found this instruction helpful
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with sm... read more

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 303 of 335 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more