Models > EPE7-21C819D > Instructions

EPE7-21C819D Hardwick Oven - Instructions

All installation instructions for EPE7-21C819D parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the EPE7-21C819D
1-15 of 71
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

bottom heating element in oven disintegrated

  • Customer: DENISE from GERMANTOWN TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 22 of 24 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I threw away the old pieces.

Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and tightened them in.

SUPER EASY!!!!!

This $40 part saved me $1500 on a new double wall oven.

Oven heating element blew out

  • Customer: Shirley from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
Removed 2 screws, pulled element out. My husband used an ohmmeter to see if the electricity needed to be turned off. It showed no voltage. He could not remove electrical connectors by hand, so he used insulated pliers. When he touched the connectors, a shower of sparks covered the inside of the oven and tripped the breaker switch. Then we noticed the pliers were welded to the side of the oven. Thankfully the pliers had insulated handles and he was not hurt. It might be a good idea to put in the instructions to TURN OFF POWER TO OVEN in the breaker panel because our oven was definitely HOT. Oven works perfectly now.

Element was burned through

  • Customer: Kevin from New London OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
I used tiny amount of WD40 on old screws,let sit for 2 minutes. Tapped the screws(2) of them with a small hammer to wake them up, I had a cordless drill and they backed right out. Pulled the old element out, used needle nose pliers to pull connectors off of the element(wiggle gently) put the new element on, reinserted back in the oven,attached with new screws that came with the element, started the oven. Worked Perfect!!!

replace light in oven

  • Customer: william from aiken SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Light Bulb

  • Customer: Terri from Kingsland TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!

needed a rack for my oven

  • Customer: steve from herald CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 10 people found this instruction helpful
i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

Element was burned up

  • Customer: James from Kerrville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Clipped the wires back onto new element and used the two stainless screws provided in kit to resecure.

It should be noted that I first called a local Maytag Appliance Co. and inquired about this element. I was told that they would have to order it and it would cost me 68.00 plus tax. I told them I knew what these elements are worth and their price was a gouge. They didn't care. This is a repair that anyone knowing how to work a Phillips screwdriver can perform. Save some money and do-it-yourself.

Thanks Partselect!

The old racks were beyond cleaning

  • Customer: Sherrie from Elverson PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
I installed the new racks

The baking element flamed out and broke

  • Customer: Michael from Wilmington DE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Fortunately, we had read the instructions on line, because none were included with the part. Still, it was REALLY easy. We unscrewed the two screws, pulled the element away from the back wall and pulled the wires off the contacts at the back. (That was the hardest part, because they were stuck-on well. WD-40 was helpful here.) The one piece of paper that did arrive with the part told us the ground wire was no longer necessary if you use the new screws that came with the part, so we ended up cutting the ground wire off. We then put the other wires back on the new contacts, pushed it back into place, and re-screwed it to the back wall. We have used the oven several times since, and it's all working well.

element burned out

  • Customer: mike from canton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I removed the two screws holding the element in place and disconnected the two wire terminals.
I then reversed the above steps to insatll the new element. SUPER EASY!!

burnt out lightbulb for over 20 years

  • Customer: Kathtleen from Bristol CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Unscrewed back plate, and replaced bulb

The plate is diffrent shape and holes was diffent .

  • Customer: Samuel from San Fransansico CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I drilled two holes on the plate and I did use same original screws.

I just wanted to say once it was installed, It worked great.

Thank you,

Sam

inner door glass cracked after a self clean cycle

  • Customer: Christina from Mentor OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
removed 10 screws on the outer door assembly, removed front glass/door panel. Continue to remove glass protector, the frame that holds the glass. Remove the layer that protects insulation and surrounds glass. Remove glass assembley, replace with new kit. Replace everything back in order. Replace door on oven. Inner screws were phillips head, the screws on the door were hex.

Lower heating element not working

  • Customer: John from Pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the two screws that held in the old part. I pulled the element out a few inches.I disconnected two wires from the old element and connected it to the new. Using the screws provided I reconnected the unit. All went well. No need for repairman. 1
All Instructions for the EPE7-21C819D
1-15 of 71