EMO4000JCC03 General Electric Microwave - Instructions

Unplug, Put Towel on cooktop. Took out screws on bottom and lowered. Removed two screws holding motor in place, Attach new motor to leads and screwed in place, Put up bottom and screwed in place. Easy, fast and works great.

removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

SOOOOO simple. Ordered drive motor. Unplug microwave. Take off bottom plate, 6 screws. Unplug wiring from motor. Unscrew drive motor. Replace with new one. Screw on, plug to wiring, screw plate back in place, plug in microwave. Walla!!! It works great.

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.

Remove bottom plate of microwave. Remove old drive (one screw) replace with new motor and replace bottom plate.

This is the second time this happened for me. The shaft for the Coupler breaks and will no longer let the plate turn. I looked at the instructions of letting the bottom of the microwave down, etc. and all I could think of is I don't think so. I used the tweezers to try to get the broken piece of the coupler but neither time was it intact. Could not locate the broken part so took the liberty of just putting the new part on the shaft, pushed down and viola I now have a turning table again. I am an 83 age female who likes to try being a do-it-your selfer. Of course there are times I am not successful but. . .By thinking back of why this part keeps breaking I think it may be my fault. I always turn the glass plate around manually when the handle of the cup or mug is out of reach. May be my fault and maybe not. Anyway this time I ordered 2 of the same parts just for future repair hopefully not needed. V.J.

Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!

Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy

I laid the new tray in the microwave. There was nothing to really install....but, the woman I spoke to in order to order the tray was terrific and I had the part in two days!! I would recommend this company every time!!!!!!

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

simply remove broken coupler and install new coupler. no tools required.

damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

How? I handed it to my husband. Done. Haha. He removed the screws, slid the grill aside, removed the old filter and slipped the new one in place. Replaced the grill and screws, viola'! Quick and easy. No sweat, so swearing. Thank you for a simple solution. It was a pleasure.