All Installation Instructions for General Electric Microwave EMO3000HBB01

Glass tray would not rotate.

Simply removed five screws from the bottom of the microwave, removed two more screws holding the drive motor and unplugged the motor. We often have the initial urge to call an appliance repair shop, but this part was easily found on Parts Select.Serial numbers on the part had changed but their photo assured me they had the right motor.

Parts Used:

Drive Motor

Craig from Centerville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

I broke the glass plate while cleaning it.

I ordered a new plate and fit perfectly. No tools. no fuss no muss. Thanks Partselect.

Parts Used:

Cooking Tray

Christopher from Cathedral City, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Noisy microwave turntable, then stopped

Reviewed the instructions on this website, was super easy, 6 screws pull off cover, 2 screws for drive motor. Done. Very satisfied.

Parts Used:

Drive Motor

DAVID from COSTA MESA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Replaced motor on turntable

Followed the instructions supplied can't have been easier. The part was on my door step the next day. It was faster than Jimmy Johns. I will use Partselect again and will recommend when I can. Thx for the great service.

Parts Used:

Drive Motor

Richard A from Sugar Grove, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

no hot

every thing is working, but no hot

Parts Used:

Monitor Door Switch

Secondary Door Switch

charlie from spring, TX
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

turn table

snaped right in. thanks ida

Parts Used:

Turntable Coupler

IDA from BRISTOL, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Broken Turntable Coupler

Pried the broken turntable coupler out with a screwdriver. Just press the new coupler down on the shaft of the small turntable motor. It is as easy as that!!!!!

Parts Used:

Turntable Coupler

Robin from Stroudsburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

parts were missing

just put them in

Parts Used:

Cooking Tray

Turntable Roller Guide

DONALD from STOKESDALE, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

The Microwave would make a grinding noise .

I removed the front plate to the microwave that had six screws and dropped the front plate down and removed the motor and installed a new one. Replaced the plate and re-plugged the microwave back in and tested the unit and was all fixed. It was a very easy installation and only took me about 20 minutes to does this

Parts Used:

Drive Motor

Floyd from Pittsburg, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken vent plastic snap

Removed old vent, removed screws - installed news vent , replaced screws and discarded old vent

Parts Used:

Vent Grille

Thomas from Pearland, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

plate broke due to excessive heating

replaced the glass tray and the part fit perfectly in place.

Parts Used:

Cooking Tray

Philip from Boulder, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Insulator around light socket Broke.

Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.

Parts Used:

Light Bulb - 40W 130V

Light Socket - 250V 75W

Karen from Springfield, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

the light over the stove top went out

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

Parts Used:

Light Bulb - 40W 130V

Light Socket - 250V 75W

charles from st augustine, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

turntable not turning.

I removed the glass tray and pulled up the coupler.I then put in the new one but it would not go down all the way down. I then noticed a piece of plastic podruding from the side of the shaft. I removed it and it fit perfectly. Job done.

Parts Used:

Turntable Coupler