This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only c...
$85.85
In Stock
Order within the next 12 hrs and your part ships today!
This part is a heater, but may also be known as a heating element, and it is meant for your dryer. This is where the heat is generated during your machine cycle in order to properly dry your clothing....
$204.50
In Stock
Order within the next 12 hrs and your part ships today!
Located at the front of the washing machine, this dryer lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 14 inches long x 11 inche...
$79.47
In Stock
Order within the next 12 hrs and your part ships today!
This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before apply...
$47.69
In Stock
Order within the next 12 hrs and your part ships today!
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer supp...
$62.61
In Stock
Order within the next 12 hrs and your part ships today!
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
$9.26
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for EIED55HMB0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sharon
August 23, 2022
Keeps blinking 88:88
For model number EIED55HMB0
Hey Sharon, thank you for your inquiry. You need to reset your dryer to fix the error 88:88. Unplug your dryer for 30 minutes, then press and hold the "temperature" and "dryness" buttons simultaneously. Keep these buttons pressed for at least six seconds to reset the dryer. We hope this will work.
Was this helpful?
Thank you for voting!
Shelbey
March 25, 2023
Can I unscrew the grate over the lint trap to be able to get the rest of the lint out? And screw it back on after of course.
For model number EIED55HMB0
Hello Shelby, thank you for contacting us. Yes, you can unscrew the grate to remove the lint housing and clean it. Please contact us anytime if you require further assistance!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replac
... Read moreing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to loca
... Read morete. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.
By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!