Quick Question!

Have you ever purchased from PartSelect.com before?

Models > EI30GS55JSA

EI30GS55JSA Electrolux Cooktop - Overview

Get Parts and Repair Help for EI30GS55JSA

If you know the cooktop repair part you need, you can browse the list of all parts on the EI30GS55JSA, or you can search by name or part description. You can also find your part by where it is located on the EI30GS55JSA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$120.02

Inner Oven Door Glass

This inner oven door glass, also called an oven heat barrier glass, is a transparent and heat resistant sheet of glass that fits into your oven or range. While containing the heat,...

$15.63

Surface Burner Cap - Black - Small 5K

Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.

$21.97

Surface Burner Cap - Black - Meduim 9.5K

Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.

$8.15

ORIFICE

$43.77

Outer Drawer Glide

As per the factory, the original part was 19 3/4 inches and the new substituted part is 16 1/4 inches. According to the factory, this part will still work with your appliance.

$8.78

ORIFICE

$6.48

SCREW

$205.57

Flat Glow Bar Igniter

This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you may need to replace this part. The flat glow bar igniter is in the back of your gas oven. You will need to remove the access panel on the back of your oven to disconnect the igniter. Be sure that the gas source to the oven is shut off before you begin this repair. This part is sold individually.

$4.26

USE WCI 316240600

$42.59

Spark Module

This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount of current to the igniter to produce that spark. If you are not getting any spark to the igniters then it is best you replace this part with a new spark module. To repair, first remove the access panel at the back of your range with a 1/4 inch nut driver to take the screws out. Next, disconnect the power harness that connects the range to the power cord to access the spark module. Take wires off using needle nose pliers and pull the spark module off the range. Match and hook up the wires to the new part. Refer to the manual provided by the manufacturer for further installation instructions and guidance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked oven door inner glass

  • Customer: Mitch from Fernandina Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 56 of 81 people found this instruction helpful
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The... read more

Broken glass interior oven door

  • Customer: stephen from garden grove, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 28 of 48 people found this instruction helpful
Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge ... read more

replacing the fan on a convection oven (fan was making a vibration noise)

  • Customer: John from Stevensville, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 10 people found this instruction helpful
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access... read more