Models > EI26SS55GW0 > Instructions

EI26SS55GW0 Electrolux Refrigerator - Instructions

All installation instructions for EI26SS55GW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the EI26SS55GW0
46-60 of 152
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator was not cooling

  • Customer: Vicki from Johnson City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Filter was dirty

  • Customer: Angel from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 19 people found this instruction helpful
Just push the button on the top right hand and pull the filter out; then proceed to instal the new one pushing it in place. It's really an easy operation!!

No Water or Ice Dispensing

  • Customer: Levi from Ambler PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Leaking water valve

  • Customer: Robert from Liberty Twp OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

freezer filled up with ice leaking from ice maker shut off valve bad

  • Customer: Harry from Orange City FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 5 people found this instruction helpful
It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

Ice maker line was freezing

  • Customer: John from Ellsworth WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

One blade broke from condenser fan

  • Customer: Chris from Lockport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

replaced door gasket

  • Customer: Langley from Delberton WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley

no water to the ice maker, have water to the front water through the door.

  • Customer: ROBERT from DOWNINGTOWN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
repair went smooth except when I was done I still had the same problem, I thought for sure the valve was bad but I guess not. don't know what it could be.

Ice maker malfunctioned

  • Customer: Myron from Tumwater WA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Fridge leaked water all over my kitchen

  • Customer: Craig from Eastlake OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 2 of 4 people found this instruction helpful
I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

Rust on Front Plate and Drive Blade

  • Customer: Wayne from Westford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 7 people found this instruction helpful
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

Refrigerator wasn't "winterized" ..This is a summer home, the cold winter cracked the water valve

  • Customer: Jimmy from west sayville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
I put the new unit up to the old one to see exactly how it goes, took the 2 screws holding the unt off...Took the 3 water lines off with adjustable wrench, put back exactly the same way and it worked with no leaks

Icemaker worked sporadically, infrequently, not at all

  • Customer: Allen from Palmer Lake CO
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

Leaking Water Vlave

  • Customer: Joe from Pittsburg PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 1 of 2 people found this instruction helpful
Just follow the instruction that come with the valve. Easy.
All Instructions for the EI26SS55GW0
46-60 of 152