Models > EHS345 > Instructions

EHS345 Caloric Range - Instructions

Installation Instructions for parts on models starting with EHS345

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with EHS345

All Instructions for models starting with EHS345
1-15 of 68
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls were burned and tacky

  • Customer: Donna from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 459 people found this instruction helpful
First I removed the old bowls and replaced them with the new.

Drip bowls needed to be replaced

  • Customer: John from Chester VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 444 of 523 people found this instruction helpful
took old bowls out, put new bowls in, took a coffee break

Old drip pans stained

  • Customer: Linda from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 210 of 412 people found this instruction helpful
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

We needed new drip pans and no one carried the model we needed

  • Customer: sylvia from ventnor city NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 65 people found this instruction helpful
we removed the old pans after first removing the electric heating element and simply inserted tne new pans

The bake element burned in half, shorted out, made the lights in the house flick and burst in to a short lived flame.er

  • Customer: Michael from Winchendon MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Exactly:
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Broiler burned out

  • Customer: David from Lewisburg TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
The Job didn’t take very long at all. I pulled the unit out and unplug it before I started the repair. I had to remove the back two access cover plates to get to the two wire leads that connect the broiler. I don’t believe there was enough wire to be able to do it all from the front side. Next I disconnected the two wires that connected it while remembering what color goes to the correct side (just incase this does matter). After removing the wires I moved on to remove the element with a Philips screwdriver. The new part already had the hangers on it so I reused the old screws and installed the new element. Next I reconnected the wires in the back and re-installed the back panels. I plugged it up and it works as good as new now. This was definitely a lot cheaper to fix this myself than hire a repairman.

The drip bowls were all caked and corroded.

  • Customer: Terry from Mountain City TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

not proper heat in oven

  • Customer: Mary from Raytown MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
ordered part -got it the next day- stalled as long as I could then opened oven removed racks-used screwdriver to loosen screws in bracket holding element on- pulled out element-used pliers to take off wires in element-thew old element as far as possible-reversed procedure to put in new element-replaced rack-received praises of all afffected-the end

Burned out bake element

  • Customer: Gregory from Norfolk VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Went together real easy , but I poped a fuse/circuit braker.
The braker would not reset at first, but we got it all working fine.

hard to get old one out

  • Customer: robert from chatham VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 15 of 39 people found this instruction helpful
easy to put in

Rivet broke on the right side oven door hinge

  • Customer: Roger from Pleasanton CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Regarding my right side oven door hinge replacement, P/N PS2172201

After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.

Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.

Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.

piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.

  • Customer: George from Irving TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

electric coils would not stay flat as drip pans were incorrect fit

  • Customer: Janet from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
replaced drip pans with correct type

Old hinge snapped a rivet. It could no longer hold the weight of the door.

  • Customer: Frank from Farmingdale NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.
All Instructions for models starting with EHS345
1-15 of 68