Models > EHS312 > Instructions

EHS312 Caloric Range - Instructions

All installation instructions for EHS312 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the EHS312
1-11 of 11
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven seals got dried and cracked

  • Customer: Brent from Goleta CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 20 people found this instruction helpful
The top seal was too long (my fault, ordered wrong length seal) so I had to cut it and high-temp epoxy the metal hook into the end. Overall pretty easy fix.

Oven wouldn't heat

  • Customer: Jack from Rouses Point NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
I disconnected the oven power, then removed the two screws that hold the element in place, then I pulled the old element out, and connected the new element to the two wires, and reinstalled the two screws. PartSelect provides easy part selection, very quick delivery, and is my first choice for hard to find parts. I have used them in the past and am always pleased with the service/price they provide.

Bake element broke in two THANKSGIVING Morining

  • Customer: Susan from Rowley MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
My husband simply unscrewed the screws on each side and put on the new bake element. Just need to remember to UNPLUG the stove as he had a few sparks at first . . . other than that, it was simple. Thanks!!!

The top seal on my Range broke

  • Customer: Clara from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was really easy! I read a review where the gentleman had order the wrong size and that had me a little worried because I did not specify a size. There were three seals on my range so I figured if one broke I might as well replace all three. When I received the seals they were the right size and it took me less than five minutes to put them on. No tools needed because they had hooks on each end. Thanks a lot!

Lower existing oven seal was missing, the top oven seal was stretched and the side seals were old & cracking. The heat leaked out of oven and food baked unevenly.

  • Customer: Deborah from Horsham PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the old stretched and cracking seals by unhooking the metal brackets from the holes at the corners of the oven, and replaced them with the new seals, which fit perfectly. It took about a minute. My 25 year old oven is working wonderfully now.

Replace oven door seals

  • Customer: James from Leesville LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The side seals were available and hooked into place with no effort at all. The OEM top and bottom seals were not available any longer so I purchased the recommended substitute which was about 2" too long. I took the advice from another of your customers and cut the top and bottom seals to the correct length and using hi-temp epoxy reattached the hooks to the shortened end. On an additional note the seal itself is partially tubular in cross-section an by that virture protects the hi-temp epoxy from the heat.

Top oven seal sagging, no longer seals

  • Customer: Martin from Blanca CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Used 2 side seals to make a new top seal (no longer available). Cut the 2 new side seals to provide about 1/2" less length than the old top seal. Removed one of the end hooks and straightened the hook, removed the old silicone from the hook. Used high temperature silicone and the old hook to splice the cut ends together. Let cure over-night and reinstalled. Works like a champ.

Replace oven seals

  • Customer: Myra from Yuma AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The side seals fit perfectly so I just put the hooks in the holes! The top seal was too long so I cut it to size and used super glue which did not hold. Next I looked for a high temp glue with no luck. Finally I put the hook into the seal and used a very fine wire through the holes in the metal of the hook piece and twisted the wire until it held the metal piece in place. Then I installed the top seal and it works fine. There is no longer heat pouring out the top of the oven and my brownies cooked at the right temp for the right time. Hooray!

The seals were brittle and broken.

  • Customer: Winford from Ringgold GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I unhooked the clips on each end and put the new seals on. Quick and easy.

Side seals were normally deteriorated on old wall oven

  • Customer: Gerard from Morristown NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I used the 14 in. Seals which are shown in their packaging as folded in a U - shape. The two tabs on either end slipped into their retainer holes easily requiring just enough stretching to flatten them. It all all took less than a minute, including opening the package. Very satisfying.

Replace top oven seal

  • Customer: Linda from Oxnard CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
All Instructions for the EHS312
1-11 of 11