EER3000H01KC General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old element burned through.
Unplugged the old and plugged the new one. replaced the covers and turned the power back on. No problems!!
Parts Used:
-
Charles from Licking, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
rust on outside bottom of door.
It is first necessary to remove the door from the range according to the manufacturer's instructions. Once removed, lay it down on a flat, protected surface with the outside facing down. Remove the two upper phillips screws and the hex nuts on the bottom channel. Next, separate the inside panel from the outside panel. You will then see the remaining hex nuts that have to be removed in order to replace either the bottom trim channel or the side pieces.
Parts Used:
-
Robert from Brighton, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bake Element Burned Up
We've had this range for almost 10 yrs and while on the clean cycle the bake element burned up. We ordered the new bake element on Wednesday and was delivered on Friday. Installation was not difficult as we followed the advice of other installation reviews. However, while removing the old element one of the wires snapped back into the insulation. We had to remove the back cover plate and found the correct wire and just pushed it through. Easy, peasy, japaneasy!
Parts Used:
-
Mary from North Freedom, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Bake burner would not heat up.
There were no burnt spots on the baking element but I turned the electric power off and removed two screws and removed the two termenals wires and replace them on the new element and replaced the two screws that I removed. I turned the electric back on. Every thing is great and it only took me fifteen minute from start to finish.THANK'S
Parts Used:
-
Louis from New Haven, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
heating element burned up
unscrew element, remove back panel of range. replaced element and reattach connectors. reistall back
Parts Used:
-
Sue from Mentor, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Heating element exploded & fire started in oven
followed instructions from the order information sheet.
Parts Used:
-
Darrell from Alamo, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Broiler unit in oven quit working.
Removed old broiler unit and installed new broiler unit. Very easy. We ordered the part on Monday over the internet and got it on Wednesday. Such speedy delivery and way in time for Easter. Thank you. Very impressed. I am keeping this site for any future repairs!
Parts Used:
-
Carol from Bolckow, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Switch would not adjust temperature
Simple; unplug stove, take back cover plate off. Pull off front knob. Remove screws holding in switch.Replace wires one at a time to avoid dis-connections - or make color coded diagram. put back together. DONE
Parts Used:
-
William from Roanoke, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burned out oven light
Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.
Parts Used:
-
Herbert from Virginia Beach, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
missing oven racks
Parts fit perfect, and order them on Wednesday and they were delivered on Friday morning. Excellent service. Thank you. Happy customer.
Parts Used:
-
Casey from Charlotte, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bake element burned out/split in two
Unscrew the two nuts in the back of oven holding the bake element,carefully secure the electrical connections with plyers so they won't go back into the stove. Slowly, pull the bake element out of the electrical sockets, one at the time. Next insert the electrical parts into the new element ends, screw back the nuts, and done!
Parts Used:
-
Magdalena from Des Plaines, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Blew the electronic Control Board
It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.
Parts Used:
-
PETE from MANCHACA, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Break in lower heat element
Removed the two racks, remove two screws from the back of heat element, carefully pull element out, unplugs wires from element, install new element in the reverse order
Parts Used:
-
Terry from Volga, SD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Bottom bake element burned out
Moved the stove away from the wall and unplugged. Removed screws from the back of the stove. Took out old element and replaced with new. Replaced the screws, plugged the stove back in and turned on the oven to make sure everything was working. Everything working fine and I baked a cake. I was also very happy how quickly I received the part. I ordered it late Thursday afternoon and received it by the following Saturday morning. Thank you.
Parts Used:
-
Rita from Bucyrus, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!
Parts Used:
-
Ruth from Potosi, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!