EER3000F01TW General Electric Range - Instructions

I turned the power off, then I removed the two screws under the top panel that have all the knobs.Then I removed two screws behind the panel,and pulled the panel twards me. By doing this the clock control is exposed.I removed the four screws that held the clock control and peeled the face plate and installed it on the new unit. I then secured the new unit to the panel with the four screws. I switched the wireing to the new control.I reinstalled the front panel two screws in the rear and two screws under the panel. Then I replaced all the knobs.This took me about half an hour. I had a good time doing it my self.I also changed the lower burner. Removed two screws,pulled the burner back and removed two wires and replaced them on to the new unit and replaced the two screws. L'm happy & so is my wife.

There were no burnt spots on the baking element but I turned the electric power off and removed two screws and removed the two termenals wires and replace them on the new element and replaced the two screws that I removed. I turned the electric back on. Every thing is great and it only took me fifteen minute from start to finish.THANK'S

unscrew element, remove back panel of range. replaced element and reattach connectors. reistall back

followed instructions from the order information sheet.

Removed old broiler unit and installed new broiler unit. Very easy. We ordered the part on Monday over the internet and got it on Wednesday. Such speedy delivery and way in time for Easter. Thank you. Very impressed. I am keeping this site for any future repairs!

My husband took care if it, very simple...took him less than 10 mins.

removed old element--had read warnings about wiring would go back into insulation--pliers slipped and one wire "jumped" back into insulation--had to take back off stove to retrieve the connection--other than that incident, the connection was simple--suggestion--make sure you have needle nosed vise grip pliers to prevent wire from becoming lost in the insulation---could not find my pliers so had to use regular pliers.

Removed old lower bake element on the inside by removing nuts at the back of inside of stove which holds element in place. Then removed metal guard panel on the outside back of stove to disconnect old terminals. Then from the inside of oven removed the old element and reconnected the new element terminals.

Easy to install replacement parts using the screws provided.

Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Simply remove the large screws from the inside of the door and the smaller screws that hold the handle on. We used a "star" tip screwdriver bit (it might be called a torx head?). Keep the smaller screws separate as they are slightly different in length. Remove the handle. Slide the vent piece off. Reassemble with the new trim piece. The stove looks as good as new. It took less than 15 minutes and we avoided the $79 repair call. One has to wonder why manufacturers use plastic parts in an area that gets so hot that it scorches when the self cleaning cycle is used?

Unplugged the old and plugged the new one. replaced the covers and turned the power back on. No problems!!

Simple; unplug stove, take back cover plate off. Pull off front knob. Remove screws holding in switch.Replace wires one at a time to avoid dis-connections - or make color coded diagram. put back together. DONE

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

Parts fit perfect, and order them on Wednesday and they were delivered on Friday morning. Excellent service. Thank you. Happy customer.