EER2001M02SS General Electric Range - Instructions

Watched repair videos on YouTube to prepare. The repair was very easy.

Disconnect old burner and reconnect new one

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

Disconnect electric at panel box. Pull oven out. Remove 5 screws from rear panel. Pull off the 2 clips at the tips of the old element which is located about 2/3 down the back side of the oven. Remove broken element from inside the oven and slide new element in place. Push 2 clips firmly on the ends of the new element. Replace back cover. Turn power on. Test oven. Slide oven back in place.

1) REMOVE ELECTRIC PLUG FROM OUTLET. 2) Pull oven away from wall. 3) Remove the 3 machine screws holding in the top piece of sheet metal. 4) remove top piece of back sheet metal 5) pull knob of the front of the switch. 6) remove the two screws holding the switch to the front of stove. 7) remove wires (needle nose is helpful) one at a time and put them in the same location on the new switch. 8) put new switch into location on the stove and screw in the two front screws. 9) replace sheet metal on the back and screw in the 3 machine screws that hold it in. 10) plug in stove and move it back into position 11) put the knob back on the front and test it to make sure it works ok. 12) be sure to remove power if you need to do open the stove again to correct anything.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

Very easy to remove the parts and to reassemble

replaced lights in refrigirator and freezer

Unplug the stow.(Important!)
Remove the knobs pulling out from front of the stove.
Remove the 2 screws from each knob.
From rear.(3 big 4 small screws to be removed)
Removing the 7 screws pull up the upper panel get access to switches.
One at a time remove the wiring from old switch attach to new switch. Screw the upper panel. Install the knobs.
Plug the stove.
You are done!
Thanks to PartSelect for their quick response.

Replacing the gasket is easy and requires no tools. Pull out the ends that are just inserted in their slots. Then work your way around the door pulling out the little metal clips from their holes. Replace the new gasket the same way.

It's even easier to do if you remove the door first and place it on a table--but it's heavy. To remove the door, flip up the hinge clips--you might need a flat screwdriver to do this if they are old and stiff as mine were. Then close the door almost all the way--you'll feel a stopping point-- and pull up. It comes right out--but again, it's heavy.

Replacing the bake element is not much harder. It's easier to do with the door off, but not impossible with the door on. First, pull out the range and unplug it. Then, remove the hex screws holding the bake element against the back wall. The element has two electrical contacts that insert into clips at the ends of wires. Pull out the wires a bit to give yourself some slack, then pull the contacts out of the clips. Insert the clips from the new element into the wires and replace the screws.

If the wires get lost behind the back wall of the oven, it's not a big deal. Just remove the narrow central panel on the back (it has six hex screws) and push the wires back through the wall opening. Then replace the back panel and install the new element.

Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was damaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.

I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!

Unscrewed the stove top and replaced the element.