EER2000M02WW General Electric Range - Instructions

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Consult the instruction guide that comes with the new part. Excluding doing some cleaning while things were apart, the operation took about 20minutes. 1. Open the oven door all the way. 2. Pull back the hinge latch on each hinge. 3. Close the door partially (about broil position). 4. Remove door by pulling so that hinges com out of the slots. 5. Carefully set door face down on a table so that inside of door faces up. 6. With a Torx driver, remove 2 screws at upper part of inside of door. 7. With a nut driver, remove screws at bottom of Door Bottom Channel Trim. 8. Lift inside of door off, being careful not to lose the spacers that are behind the door panel at the upper part of the door. 9. With the nut driver, remove 4 screws that hold bottom trim to the side trim pieces. 10. Remove the old trim and replace with the new. 11. Align the left, right, and bottom trim pieces. 12. Reattach the 4 screws that hold the bottom trim to the side trim pieces. 13. Carefully replace the inside door panel, making sure the spacers are aligned properly between the main door pieces. 14. With the Torx driver, replace the 2 screws at the upper part of the inside of door. 15. With the nut driver, reattach the bottom screws at the bottom of the trim piece. 16. Carefully reinsert the door hinges into the slots (the door must be in the approximate broil position). 17. When hinges are properly inserted, door may be opened all the way. 18. Push the hinge latches back into hinges to secure door to oven.

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
- remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.

I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.

The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.

Watched repair videos on YouTube to prepare. The repair was very easy.

Disconnect old burner and reconnect new one

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

Disconnect electric at panel box. Pull oven out. Remove 5 screws from rear panel. Pull off the 2 clips at the tips of the old element which is located about 2/3 down the back side of the oven. Remove broken element from inside the oven and slide new element in place. Push 2 clips firmly on the ends of the new element. Replace back cover. Turn power on. Test oven. Slide oven back in place.

1) REMOVE ELECTRIC PLUG FROM OUTLET. 2) Pull oven away from wall. 3) Remove the 3 machine screws holding in the top piece of sheet metal. 4) remove top piece of back sheet metal 5) pull knob of the front of the switch. 6) remove the two screws holding the switch to the front of stove. 7) remove wires (needle nose is helpful) one at a time and put them in the same location on the new switch. 8) put new switch into location on the stove and screw in the two front screws. 9) replace sheet metal on the back and screw in the 3 machine screws that hold it in. 10) plug in stove and move it back into position 11) put the knob back on the front and test it to make sure it works ok. 12) be sure to remove power if you need to do open the stove again to correct anything.

Very easy to remove the parts and to reassemble

replaced lights in refrigirator and freezer

Read the instructions on how to remove the door, found in the owners manual. Once you release the hinge lock latches, the door can be lifted off of the hinge arms.

It is fairly heavy and bulky. I spread a large towel on the kitchen table and placed the door, front side down on the towel.

Remove the 3 nut screws at the bottom of the door and then lift the inner door assembly up about 3" and hold it up temporarily with a medium sized plastic food storage container. This will allow room to access the 4 nut screws (2 on each side) that secure the trim to the door.

The old trim was somewhat difficult to remove because of years of rust and other build up where the front door glass goes behind the trim. Be careful not to damage the glass. I used a putty knife.

The edge of the glass will be soiled so I used a mild abrasive cleaner to remove the rust and grime, and then used a window cleaning spray to clean the glass.

The new piece had to be "fitted" slightly to match the existing screw nut holes but it goes together quickly.

Took me a second to remember that YouTube is just as handy a tool as what I've got in my toolbox. The installation of the new glass was as easy as apple pie. Anybody that has ever used a screwdriver could manage that fix and do so single handedly. PartSelect.com came through with an easy-to-navigate website, a very reasonable price range and anything you could ask for to help fix whatever has broken. I quoted a gentleman in my town, a handyman, and he came back with a price tag of over $300 for parts and labor! Even with tax, shipping and the new glass I came in well under $100, and the labor was next to nothing. If i ever have to replace or fix something in my house again, I'll be using them, Without a doubt. Thanks for everything, dudes. Cheers!