EDW6100N00WW General Electric Dishwasher - Instructions

1. Remove the outside panel on the door by removing 10 phillips screws on inside of door. Outside panel will drop loose - do not let it drop.
2. There are 3 electrical plugs that will have to be removed. The first is a 2" long quick connect in the upper middle of the door panel - it will pull straight out. Remember where it makes its connection. Now the exterior door panel will drop down to the floor, pivoting on two axle screws at the bottom. The interior panel can be left vertical for ease of access.
3. The other two electrical connections are on the left side of the old dispenser and can be removed with a simple pull to the left.
4. Remove the six (6) phillips screws from the panel that hold the dispenser in position. Two retainers will also drop off, which hold the dispenser top and bottom.
5. Angle the dispenser and work toward the inside of the dishwasher, turning as necessary to remove from the opening.
6. Reverse the process for installation. Remember to reconnect all three electrical connections.

Once upon a kitchen dreary.
Washing dishes made me weary.
All the dishes would not clean.
Gunk clogged up my filter screen.
The lower spray arm stuck and rattled.
With flying muck my dishes battled.
The muck had won and I had lost.
The repairman said it would really cost.
And so I did a google search.
Partselect got me out of a lurch.
Correct parts were easy to choose
and service so quick I couldn't lose.
I took off the old parts and tightened the new
No tools were needed my fingers flew.
And now my dishes come out clean
I feel competent and frugal, you know what I mean?

In order to access the fill valve, dishwasher had to be removed from under countertop. Disconnected water supply line and drain hose under sink. Unplugged unit and removed 2 screws holding unit to countertop. I was then able to pull unit out and replace valve. After reinstallation, the same problem existed. Further research pointed to the control module, approx. $100.00 or the motor, approx. $250.00 - $300.00. I than began looking at new dishwashers, but I did email GE with the problem. They suggested I use citric acid or vinegar in hot water, pour into right rear portion of tub and wait 1/2 hour. After doing that, the dishwasher worked perfectly.

I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.

Just put axle and wheel together and popped them on. Thank you. I know you saved me a bundle.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

pulled the racks out, replaced the broken parts....easy job

Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.

Dishwasher would not drain. I confirmed it was the drain pump by starting the DW and pressing reset 10 sec. later. When functioning properly, pump will engage and drain the DW. In my case, nothing except a blinking light for 30 sec. I turned off power at circuit breaker, remove base plate (no need to pull dishwasher), disconnected pump from hose (DW side) and caught water, disconnected hanger hook from DW (requires a little twisting), disconnected on house drain side, marked two sets of wires (1,2), removed wires by shoving nail into coupler (otherwise hard to disconnect), and removed pump. Repeat in reverse order to connect new pump.

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled