All Installation Instructions for General Electric Dishwasher EDW6000L15CC

Three of the 8 wheels broke.

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Asok from HELOTES, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

drain pipe was missing when purchased used dishwasher

oversized outlet not available in local stores, this one fit perfectly

Parts Used:

Drain Tube Kit

arthur from ALMENA, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Would NOT drain

Flipped washer on side
Did repair from bottom
Really easy repair

Parts Used:

Motor and Drain Pump

Nathaniel from HAWKINSVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old lower dish rack had rusted in places due to some of the protective coating wearing off.

It is extremely easy. Just take out the old lower rack and slide in the new rack. Remove the silverware holder from the old rack and insert it into the new rack.

Parts Used:

Dishwasher Lower Dish Rack with Wheels - Gray

John from TEMPLE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Small 1/8" hole in side of inlet sump.

Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.

Parts Used:

Inlet Sump

Ron from HODGES, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove

Put new basket in, threw old one away

Parts Used:

BASKET ASM SILVERWARE

Diana from NAPLES, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rinse cap was broken

Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions

Parts Used:

Detergent Dispenser with Rinse Cap

DENNIS from MAUMEE, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced dishwasher but had the wrong drain hose.

Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.

Parts Used:

Drain Tube Kit

CLAMP

Victor from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The water inlet valve on the dishwasher leaked.

The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.

Thank you.

Parts Used:

Water Inlet Valve

John from Andover, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

at start of the wash cycle did not take in any water

very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

Parts Used:

Water Inlet Valve

wojciech from bayonne, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench set

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

a couple of retaining ears were broken from the cover allowing the the switches and plunger to move out of place

took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down

Parts Used:

Interlock Cover

charles from royal oak, MI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leak from inlet valve

Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.

Parts Used:

Water Inlet Valve