EDW4000G10BB General Electric Dishwasher - Instructions

Watched the How To video. Removed and replaced each arm. The bottom arm comes off by just by turning and lifting. The middle and top arms required the removal of a screw with a socket wrench. So simple that my wife actually had it done before I got to it.

Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.

NOTE I have classified this is a DIFFICULT JOB, but NOT because of the mechanics involved [including the electrical connectors UN-plugging and re-plugging, BUT DUE to the ANALYSIS you need to do to determine whether the SOAP DISH PART or the CONTROLLER is at fault. And this ANALYSIS will probably require you to get into the DISHWASHER DOOR twice. Once to do the analysis and then again to replace whatever part you target. Being you will want to continue to use the DISHWASHER by manually dropping the soap door [or just soap] at the appropriate time in the cycle, while awaiting the new part, which means you have re-button up the door and take it apart again when the new part arrives. . Before starting, view PartSelect's VIDEO on replacing the SOAP DISPENSER, but ignore THE STEPS OF REMOVING AND REPLACING THE SOAP DISPENSER.PART, at this time. The analysis starts with MANUALLY trying to activate the mechanical soap door release on the back of the mounted SOAP DISPENSER, with the soap door closed. It should take only ounces of downward pressure [towards the door hinge] on the vertical plastic piece in a channel near the center of the dispenser, to release the soap door. Next if you have access to an OHM METER {or MULTIMETER} or a DC POWER SUPPLY [to test the the activation of the door release] pull the two connectors on the SOAP DISH SOLENOID [a set pointed pliers will be helpful, as outlined in the VIDEO]. If measuring the SOLENOID's resistance it should read roughly 1800 OHMS. If using a DC POWER SUPPLY, you will probably need at least 25 volts DC to trigger the SOLENOID [NOTE I do not have a variable DC POWER SUPPLY to check it out nor do I know the voltage that the DISHWASHER uses]. Do not bother to measure the resistance of CONTROLLER's driving circuitry [the two wires having connectors], as it will read INFINITY, regardless of whether GOOD or BAD, The CONTROLLER apparently uses a RELAY on this circuit, as opposed to some kind of solid state switch. Replug the SOLENOID connectors. Re-buttoned up the DISHWASHER as shown in the VIDEO, assuming you are going to continue using it If you determine no problems in the above tests, then consider it a CONTROLLER pro0blem and you will need to order one. Otherwise you should have found indications of a SOAP DISPENSER PROBLEM. . When the replacement part arrives and you ready to install it, refer again to PartSelect's VIDEO on replacing the Soap Dish Dispenser for a refresher Following the VIDEO completely, if you replacing the DISPENSER. If you are replacing the CONTROLLER, once inside the DOOR, you will need to remove around 6 individual electrical connectors [before doing ANYTHING REMOVE POWER from the DISHWASHER [as instructed in the VIDEO}. These connectors [all but any single wire connectors] are designed to be plugged only one specific way, so when re-plugging NEVER FORCE a connection, The best way to make sure you do not get confused, take a picture of all the connectors -OR- make notes on the looks and orientation of each multi-wire connector. There is one mounting screw on right side of the CONTROLLER. When installing the new CONTROLLER there are mounting EARS on the left side that are first engaged by having the CONTROLLER tilted up on the right side. Replace the mounting screw. Replugged all the connectors using whatever guide you made. Proceed to put the DOOR back together as outlined in the VIDEO.

Put the wheel on the stud/axle first THEN push wheel/stud/axle assembly onto lower dishwasher rack.

Check website, order part. Hardest part was determining which was the right part. Needed the axle--I call it the hanger. I had previously called and ordered, but only received the wheel with no way to attach it. Push the axle into the wheel. Push the axle onto the rack. Since it was new, it didn't slip right on, and had to push it hard. (However, when it snapped on, three of the other wheels and axles came off.) Had to put them back on as well. Much easier, as they were older and not as snug. Total time: Took longer to open the package than put it on.

I sopped up all the water in there and pulled out the lower rack, then disconnected the electricity and water pipe and drain hose. Then I unscrewed the front kick plate/cover and removed that. Then I unscrewed two screws at top of unit from the counter top, and pulled the unit out. It is surprisingly light weight. I rolled it over on its right side, and took off the short drain hose where the flapper is, and pulled the old one off and put the new one on and reversed the procedure to reinstall. It was very easy to fix, especially with your Youtube video! THANKS

Snap the stub/axle into the wheel and snap the assembly on the rack. EZ! This solved the issue where the original wheels (through age) were falling off the rack and the rack would bump over the gap between the body of the dishwasher and the door.

We we're installing a used dishwasher,had to take it back out and replace the water inlet valve.

Ge dropped the ball when they designed the bottom rack. The wheel assembly has two parts a side clipping axle and the wheel. It must be a huge problem in that as soon as you do a search a picture of the these two parts shows up in the first page. $7. 50 As a replacement. There are eight (8) wheel assemblies to deal with. Usually one or two start to fail but the proper remedy is to replace only the axle clips and all of them. ($. 79 Each) reusing the old wheel is key in keeping the cost down. The wheels are not the problem. The easiest way to remove the old axle is to pinch the axle ends. And pull on the clip assembly. Push the new axle clip onto the wheel prior to attaching the clip to the rack. The whole eight clip w/ wheel replacement will take less than 6 minutes. D. Hackett spring hill tn

I read some other fixes on this site. I received the new gasket folded it in half and just pressed it into the channel. Super easy fix.

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

Wow... Simple... Just pulled the old broken axle off, pushed the new wheel onto the axle then snapped onto the wire basket. Ez and cheap repair but it keeps an off balance dragging sliding from causing more damage.

Used needle nose pliers to get them off.G

Just removed the prior rack and put the new one in. Much improved design on the wheels and rack seems of better material as well. The rack does not have as many holders as the prior rack dishes and pans do not fit as well.

Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .