Models > EDW3060G02SS

EDW3060G02SS General Electric Dishwasher - Overview

Get Parts and Repair Help for EDW3060G02SS

If you know the dishwasher repair part you need, you can browse the list of all parts on the EDW3060G02SS, or you can search by name or part description. You can also find your part by where it is located on the EDW3060G02SS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for EDW3060G02SS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the EDW3060G02SS [Viewing 3 of 3]

$9.93

Lower Rear Rack Wheel and Axle Kit

This kit contains one wheel and one axle. It is designed for the rear lower dishrack. Sold individually. Order quantity needed.

$0.69

RACK SLIDE END CAP

This part attaches to the rails, for the upper rack, to prevent the dishrack from sliding all the way out.

$8.77

Lower Front Dishrack Wheel

This wheel is located on the front lower rack. It is sold individually and comes with the attaching axle.

$10.69

Upper Roller and Axle - Kit of 4

$7.02

Corner Tub Baffle - Lower Left

The left and right side baffles should be installed/replaced at the same time. Right side baffle is sold separately.

$7.02

Corner Tub Baffle - Lower Right

This baffle fits the lower right hand corner of some dishwashers. It is black and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and right at the same time.

$46.61

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$53.64

Door Gasket - White

This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.

$10.02

Piston and Nut Assembly

This is used for the check valve.

$14.73

Silverware Basket with Lids

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The rollers on the upper rack broke

  • Customer: Carl from Fairfield TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 465 of 466 people found this instruction helpful
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers ... read more

Lower rack wheel was melted

  • Customer: Mark from Huntingdon Valley PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 462 of 463 people found this instruction helpful
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience. read more

Wheel broken off bottom rack

  • Customer: Julie from Maumee OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 460 people found this instruction helpful
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done! read more