Models > EDW3000G00BB > Instructions

EDW3000G00BB General Electric Dishwasher - Instructions

All installation instructions for EDW3000G00BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the EDW3000G00BB
1-15 of 598
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken upper rack roller, rack kept falling off the track

  • Customer: Doug from Columbus OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 367 of 370 people found this instruction helpful
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

Rollers fell off lower rack of dishwasher.

  • Customer: Lloyd from The Villages FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 363 people found this instruction helpful
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.

The stud assembly in the middle of each wheel no longer stayed inside the wheel.

  • Customer: Wendy Baldwin from Stowe PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 361 of 365 people found this instruction helpful
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.

Rack falling off of upper slides

  • Customer: Eric from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 186 of 254 people found this instruction helpful
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

wheel replacement

  • Customer: michael from perry hall MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 215 of 403 people found this instruction helpful
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

Dishwasher wouldn't fully drain

  • Customer: Dan from Minnetonka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 98 of 108 people found this instruction helpful
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.

wheels were worn out and kept falling off

  • Customer: JOHN from PURCELLVILLE VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 65 of 67 people found this instruction helpful
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.

front twoo rack rollers broken ,bottom rack roller broken

  • Customer: Russell from Pueblo CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 74 of 136 people found this instruction helpful
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,

Dish washer is not running through cycles

  • Customer: mike from huntley IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 41 of 51 people found this instruction helpful
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...

Rollers broke off from bottom rack of dishwasher

  • Customer: Reginald from Hamilton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 127 people found this instruction helpful
Went to www.PartSelect.com. Part was easy to locate online with GE model number and illustraion online. They shipped the parts in two days and I put the new parts on by hand. Saved a $135 service call from GE. One part came in broken from the factory. Upon calling customer servce, PartSelect sent out a replacement part the next day - no problem. Great service, would be happy to use again - Thank you!

Broken wheel

  • Customer: Bennett from Burke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 63 of 124 people found this instruction helpful
Siimply removed the rack and replaced the wheel assembly. Very easy

LOST A WHEEL FOR DISHWASHER

  • Customer: LINDA from OCALA FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 63 of 124 people found this instruction helpful
REPAIR EASY..SNAP IT IN......IMPRESSED WITH THE SPEEDY DELIVERY. THANKS

Rubber connector was leaking (slit in rubber)

  • Customer: David E from Colorado Springs CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 35 of 41 people found this instruction helpful
First I removed the dishwasher from underneath the countertop and laid it on its back. I used a nut driver to remove the pump support wire and the two clamps holding the rubber connectors to the pump. It helped to hook the pump support wire in a hole in the left side of the frame and reconnect it to the pump to hold it up out of the way. I was able to remove the rubber connector by hand and unscrew it. To install the new rubber connector tightly, I slipped a piece of 2" PVC pipe (outside diameter is 2-3/8") inside the connector and tightened the clamp around the connector and PVC pipe. This allowed me to use the pipe to tighten the rubber connector. I reassembled the dishwasher pump and connections and put the dishwasher back into service

Dishwasher would not drain completely,

  • Customer: Daniel from South Elgin IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 44 people found this instruction helpful
Found a forum on the internet that said the Air Check Valve located under the screen on the bottom of the back wall inside the wash compartment may be the culprit. Took it out by using nut driver to remove screen, and twisting the part out. The seal was deteriorated. Repleacing the part was simply the opposite, and very easy.

I also replaced the screen on the floor of the wash compartment because the rubber was deteriorating there too. Here I had to remove the spray arm by carefully prying the locking tabs outwards and lifting the entire spray assembly upwards. Then, then plastic covers need to be unscrewed and removed. The new part had the plastic cage molded into it. So I discarded the old plastic cage. There are a couple of retaining clips that are a little tricky to get off the plastic posts. But, they can be removed by prying a standard screw driver underneath and working them off the post. Do not break the plastic post, and save the retaining rings. The new part does not come with any screws or retainers, so you will need to re-use them. Simply, place the new screen in position, slide on the retaining clips, and screw down the cage. The spray assembly is just slid back onto the shaft and snaps into place. A lot of writing, but was rather simple to do. 15-20 minutes.

Wheel fell off dishwasher rack, landed on heating element and melted.

  • Customer: Stacey from Spring TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 63 of 125 people found this instruction helpful
Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.
All Instructions for the EDW3000G00BB
1-15 of 598