Models > EDW2050F00CC

EDW2050F00CC General Electric Dishwasher - Overview

Get Parts and Repair Help for EDW2050F00CC

If you know the dishwasher repair part you need, you can browse the list of all parts on the EDW2050F00CC, or you can search by name or part description. You can also find your part by where it is located on the EDW2050F00CC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for EDW2050F00CC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.70

Piston and Nut Assembly

This is used for the check valve.

$51.16

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.

$15.80

Silverware Basket with Lids

This is a basket for washing flatware or silverware in your dishwasher.

$3.62

Hinge Arm Link

$157.21

Motor and Pump Kit

This pump and motor kit replaces many old style pump and motor kits that were manufactured since 1970. The instructions are included with this kit to help you to make it adaptable ...

$9.43

Rinse Aid Fill Cap

This part helps keep the rinse aid the dispenser until its needed.

$116.59

Lower Dishrack Assembly with Wheels

This is a dishrack kit that includes the complete rack with wheels and also the silverware basket (not pictured).

$40.45

Drain Solenoid Kit

This kit includes the armature and linkage assembly.

$9.71

Pump To Wash Arm Rubber Connector

This connector has female threads.

$36.95

Upper Rack Slide

This slide is mounted to each side of the upper cabinet wall. The dishrack wheels roll inside this track, which guides the upper rack.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher wouldn't fully drain

  • Customer: Dan from Minnetonka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 113 of 125 people found this instruction helpful
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solv... read more

Dish washer is not running through cycles

  • Customer: mike from huntley IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 57 of 68 people found this instruction helpful
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble... read more

D/W would not drain. Water standing in bottom.

  • Customer: Ed from Cornelius NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 43 of 49 people found this instruction helpful
It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.

After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in ... read more