Models > ED5LHEXTD00 > Instructions

ED5LHEXTD00 Whirlpool Refrigerator - Instructions

All installation instructions for ED5LHEXTD00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ED5LHEXTD00
46-60 of 1,022
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice dispenser would not dispense ice through the door

  • Customer: Larry from Garner NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 21 of 23 people found this instruction helpful
First I unplugged the frig, and turned offed the water and ice dispenser using the on/off panel switch. I removed the panel by inserting a small flat blade screwdriver at the bottom of the panel where the plastic studs locked the panel in place. By inserting a little upward pressure, the panel popped right ouff. The Micro Switch was very easy to remove and replace. Just make sure that the plunger on the ice dispenser makes solid contact with the switch when depressed.

Ice dispenser would not operate

  • Customer: John from Poway CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 21 people found this instruction helpful
The control bracket is made of plastic and holds two microswitches that activate the ice dispenser and the water dispenser. The plastic clips that held the switches on the control bracket broke so that the switches no longer operated when the ice dispenser lever was operated.

Two screws held the external dispenser bezel, and two screws held the control bracket in place. The wiring and switches were transferred to the new bracket and the new bracket screwed into place. Then the bezel was replaced.

Total repair time was less than 5 minutes. The control bracket was $16.50 with shipping and arrived two days after I placed the order.

The PartSelect website had a clear diagram of the control bracket so I was comfortable with the order.

Excessive noise was coming from the freezer section of my side be side refrigerator

  • Customer: Jon from Houston TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 20 of 21 people found this instruction helpful
Cleaning out the freezer took the longest time. Once the freezer was clean I turned off the freezer which did not deactivate the light in the freezer. This is a tight area to work in and not having to hold a flashlight made the job much easier. I then removed the shelf slider brackets for the 3 lower pullout drawers. The next step was to remove the interior aluminum back panel (6 screws) which covers the evaporator motor and the coil. Before removing the 3 electric wires that are attached to the evaporator motor make sure the power is off to the motor. The removal of the motor was fairly straightforward and I would suggest removing the plastic fan blade first and then the connector wires. It helped knowing in advance that the plastic fan blade would come off with a little prying. Be careful when prying the fan off so that you don’t damage the plastic motor mount bracket. Once you have installed the motor I would suggest turning the freezer back on to make sure that the evaporator motor works before reinstalling the aluminum back panel and slider brackets.

Our six year old fridge would not stop running - everything was frozen. Found if I tapped on the Tstat I could sometimes get it to turn off.

  • Customer: Jeff from Belleville WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 20 people found this instruction helpful
Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!

broken shelves

  • Customer: Maria from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 25 of 38 people found this instruction helpful
replaced with new shelves

refrigerator was intermittently cooling because thermostat contacts burned away.

  • Customer: Dennis from Westlake OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 19 people found this instruction helpful
Turn off the fridge and unplug the power. Inside the refrigerator unit, remove two plastic panels extending from the front to the rear cooling vent by unscrewing two screws. Gently unhook the thermostat tube from the rear vent.

On the control panel, gently pry off the two control knobs and the front control panel. Remove four screws to drop down the control assembly. Unplug the left electrical connector and unscrew the lever control arm being careful not to bend it. Disconnect the right side electrical connector and you can now remove the control unit to a table to easily work on it.

Undo two screws to remove the thermostat bracket. Undo two more screws to remove the thermostat assembly. Install the new thermostat and reverse the process just described. It takes about 15 minutes if you know what to do ahead of time. You will have to reuse the plastic tube that covers the thermostat sensing tube.

shut off arm broke

  • Customer: Thomas from Va. Beach VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 24 of 37 people found this instruction helpful
open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done

Ice maker would only deliver crushed ice not cube's

  • Customer: MICHAEL from NORTH PORT FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 23 of 34 people found this instruction helpful
Switched Electric breaker to off. Removed all food and ice cube tray from freezer. Remove 4 screws on soleniod cover in rear of freezer. Removed two screws, two elec connectors from old soleniod and removed. Installed new soleniod. Reinstalled elec connectors and screws, ice cube tray and food. Turned breaker on . Ice maker worked properly.

Door chute broken

  • Customer: Dwight from Marietta OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 21 of 30 people found this instruction helpful
First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Broken Door Shelves

  • Customer: Russell from Twin Peaks CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 25 people found this instruction helpful
I ordered the parts, three days later they were in my hands, and installed in the door of the refrigerator. Total time, two minutes! Perfect fit. Ordering the parts was the easiest thing I have ever done. This site is the best! Thank You!

Ice Dispenser won't eject ice cubes

  • Customer: Richard from Lynchburg VA
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 20 of 28 people found this instruction helpful
I assumed the motor had burned out. I removed the 4 hex-head screws to remove the bracket holding the motor. I had to squeeze the electrical fitting to the motor located in the right rear of the compartment in order to electrically disconnect the motor, since the lower part of the fitting has a latch that prevents its easy removal. Then I could insert a vice grips on the shaft and on the coupling in order to (reverse) unscrew the coupling from the motor. I initially received the wrong replacement motor, but when the correct one arrived, it installed on the mounting bracket easily and I reinstalled the bracket with motor easily. It turns out a new motor did NOT fix the problem, so I'm not sure what to do now.

BROKEN SHELF BRACKET

  • Customer: Thomas from Leesburg FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 20 people found this instruction helpful
REMOVED FOOD ITMES ON BROKEN SHELF. REMOVED OLD GLASS SHELF COVER. REMOVED BROKEN SHELF BRACKET. INSTALLED NEW SHELF BRACKET. INTALLED NEW GLASS SHELF COVER. REPLACED FOOD ITEMS BACK ON SHELF

Water running out of cold water in freezer door

  • Customer: Jackie from Niota TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 18 of 23 people found this instruction helpful
took back of refrigerator, removed water lines, removed electrical connections. removed 2 screws holding water valve, replaced water valve, replaced electrical connection, replaced water lines. Put back on refrigerator. Tested water on freezer door. Didn't work, had to take refrigerator back off again and check the electrical. I didn't get one of the connection put on securely, Put back on refrigerator, check water on freezer door. It worked. Make sure the electrical connection are connected this will sav you about 10 minutes of repair time

meat pan and crisper pan broken runners

  • Customer: James from Troy OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 20 people found this instruction helpful
due to over filling and closing the drawers with the door and kicking, the plastic runners broke. Also, over filling the drawers did not help.
AS for the repair, the only difficulty was getting the right drawer in the right spot. Since I replaced both the veggie and meat drawer at the same time, I got them confused. On drawer is longer than the other. other than that, no problem.

The black plastic or teflon coating on the ice mold was coming off in flakes and freezing in the ice cubes

  • Customer: Roger from Sunnyvale CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 23 people found this instruction helpful
I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.
All Instructions for the ED5LHEXTD00
46-60 of 1,022