Models > ED2KVEXVQ01 > Instructions

ED2KVEXVQ01 Whirlpool Refrigerator - Instructions

All installation instructions for ED2KVEXVQ01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ED2KVEXVQ01
796-810 of 869
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic hinge attached to chute door broke

  • Customer: James from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video showing how to disassemble unit and it showed that there was a heat element inside the chute door under the foam seal that needed to be removed and placed in side the new chute door. I spent about 10-15 minutes trying to salvage the element but the adhesive used would not release and the part was rendered unusable. I called the help line and was told that their instructions on that kit said the heating element was no longer required. I finished putting the kit in and the unit works fine

ice maker door failed to close causing frost to form preventing proper operation of icemaker.

  • Customer: Melinda from Owasso OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

Ice dispenser was broken

  • Customer: Helen from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.

Ice despenser stoped working, auger motor worked if door flap was opened fully manuallyw

  • Customer: Jolene from Merritt Island FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Googled the problem and after reading several posting & suggestions decided that the Ice dispenser kit would probably solve the problem. I ordered both parts on the chance that it might be only the micro switch and it was only a $10 part, the ice dispenser kit was $50. The access was really easy and the switch was installed in about 20 minutes but did not solve the problem so I proceeded with the kit. The parts came out fairly easy but our actual set up was slightly different from the video and print instructions. Our model did not have the heating ribbon on the door flap and the little barrel part was permanently attached to the refrigerator so I thought I could be in trouble. Did not realize that we had cracker the lever bracket clip during removal so my husband "brainstormed" a fix. That's what we needed the large head screw and drill for. We drilled the screw into the refrigerator so it holding the spring loaded piece tightly in position. Works fine. I was told my a repairman over the phone that the dispenser was probably not fixable on our model. I saved an expensive service call AND GOT THE DISPENSER WORKING!

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Door was stuck open

  • Customer: Stewart from Crosby TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
If you follow the video to the letter it's a piece of cake

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Refrigerator Freezer Ice Door Broken

  • Customer: Peter from Wildomar CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Job went as per your terrific video. Except that when attempting to retrieve the old heater element the glue on the old door was no long pliable. I had to literally tear the old foam apart to get at the heater element and almost damaged it. Not to worry. It worked out well and all is great. Thanks for the very instructive video.

ice chute door was warped allowing warm air into chute causing freeze up of chute. Would my dispense ice.

  • Customer: Peter from Westminster SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

Ice dispenser on door was disfunctional

  • Customer: Wayne C. from Metairie LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

Broken Water Filter Cap

  • Customer: Pat from Newton NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did you know you have to press the button next to the filter before you pull on the filter cap? Like most week end warriors, I just pulled the cap and of course, I broke it! The repair was simple, hopefully, in six months I will remember to press the button!

broken water filter cap

  • Customer: Sandra from Ashburn VA
  • Difficulty: Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
new filter cap fit perfectly, but I couldn't get filter in or out. Called appliance repair person who pushed it in -- no problem. I just didn't have enough arm force to push it in.

Broken cap on water filter

  • Customer: David from Wiliamsburg VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
With new cap, align slots on cap with grooves on water filter, and snap in place. Easy.

Water filter cap on my Whirlpool refrigerator was inadvertently disposed of in one of my earliest filter change efforts. I needed to replace it for esthetics and personal peace of mind.

  • Customer: Theodore from Albukuerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the replacement filter cap. Received it, cut open plastic shipping envelope after unsuccessful attempts to tear envelope by hand, snapped cap in place; Wallaah, project completed successfully!!!
All Instructions for the ED2KVEXVQ01
796-810 of 869