Models > ECKMF86

ECKMF86 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for ECKMF86

If you know the ice maker repair part you need, you can browse the list of all parts on the ECKMF86, or you can search by name or part description. You can also find your part by where it is located on the ECKMF86 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for ECKMF86 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

$87.12

Add-On Icemaker Assembly

This part number matches the current model number "ECKMF86".

This icemaker kit comes with a flat plug, wiring harness, fill tube, water inlet valve, ice bin, mounting hardware, and instructions.

Sections of the ECKMF86 [Viewing 2 of 2]

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$3.76

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

$15.79

Water Fill Cup and Bearing

$3.56

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$37.57

Single Outlet Water Valve Kit

The water inlet valve is a solenoid-operated switch located at the bottom of the refrigerator. When it is energized by electrical power, water is released from the supply line thro...

$24.48

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

$67.84

Ice Mold

This ice cube mold and heater assembly has a flake resistant surface. It is used with modular style icemakers on some refrigerators.

$3.96

Compression Nut

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$4.46

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 299 of 358 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker stopped working

  • Customer: Robert from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 72 of 82 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed t... read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 65 of 72 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more