Models > ECKMF831

ECKMF831 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for ECKMF831

If you know the ice maker repair part you need, you can browse the list of all parts on the ECKMF831, or you can search by name or part description. You can also find your part by where it is located on the ECKMF831 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for ECKMF831 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

$87.12

Add-On Icemaker Assembly

This part number matches the current model number "ECKMF831".

This icemaker kit comes with a flat plug, wiring harness, fill tube, water inlet valve, ice bin, mounting hardware, and instructions.

Sections of the ECKMF831 [Viewing 2 of 2]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.96

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

$3.76

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$35.74

Single Outlet Water Valve Kit

The water inlet valve is a solenoid-operated switch located at the bottom of the refrigerator. When it is energized by electrical power, water is released from the supply line thro...

$3.96

Compression Nut

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$4.46

Icemaker Drive Gear

$2.70

Water Hose Clamp

These tube clamps are sold individually. The screw is not included.

$3.54

SCREW

$3.54

Spacer

$2.72

Water Inlet Hose Washer

Sold Individually. Order quantity needed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 56 of 62 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more

no water getting to ice maker

  • Customer: Kevin from Boston MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 34 of 40 people found this instruction helpful
The ice maker had been slowly dying and one day just stopped making ice. No water was getting to the trays.

I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.

I ordered the part Friday afternoon. It was delivered Saturday. I did the repair in 10 minutes.
read more

Water valve failed, flooded kitchen

  • Customer: James R from Valley Springs CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
Turned off water supply and unplugged appliance. Removed lower panel on back of refrigerator with 1/4 " nutdriver. Then removed supply line, and line to icemaker. removed valve from back panel and replaced with new valve. wrapped water connections with teflon tape, turned on supply line, checked for leaks, everything o.k..Replaced back panel and in 45 minute... read more