Models > ECKMF64

ECKMF64 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for ECKMF64

If you know the ice maker repair part you need, you can browse the list of all parts on the ECKMF64, or you can search by name or part description. You can also find your part by where it is located on the ECKMF64 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for ECKMF64 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

$87.12

Add On Ice Maker Kit

This part number matches the current model number "ECKMF64".

This ice maker add on kit is used in conjunction with porcelain lined refrigerators whose cabinets are 30-33 or 36 inches wide. This round plug kit comes with a wiring harness, a fill tube, a water inlet valve, an ice bin, mounting hardware, and instructions.

Sections of the ECKMF64 [Viewing 2 of 2]

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$15.79

Water Fill Cup and Bearing

$3.56

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$37.57

Single Outlet Water Valve Kit

The water inlet valve is a solenoid-operated switch located at the bottom of the refrigerator. When it is energized by electrical power, water is released from the supply line through the water valve and into the compact icemaker mold. ***Please NOTE: This part has been redesigned and may appear different than the original. It has a new quick connection. To install: cut the retaining nut off the existing water line and gently push into new valve. To remove: depress the ring that the tube slides into.

$24.48

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

$67.84

Ice Mold

This ice cube mold and heater assembly has a flake resistant surface. It is used with modular style icemakers on some refrigerators.

$3.96

Compression Nut

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$4.46

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 293 of 352 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker stopped working

  • Customer: Robert from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 69 of 79 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed t... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 58 of 71 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more