ECBP85WJ3WW General Electric Range - Instructions

I had read some accounts of the terminal wires pulling back into the insulation, and, sure enough, one of them did before I could clip it. Even at that, pulling the stove out and removing the four nuts that held the shield in place only added another five minutes, tops. The whole thing took less than 15 minutes to change. One nut driver removes the two nuts that secure the bake element to the back of the oven, and also fits the four nuts on the shield on the back of the stove. Very easy repair, thanks to the advice given by others on this site. Thanks.

1. Pull range out from wall and disconnect power cord from outlet. 2. Remove 5 screws to remove panel on back side of range to expose the bake element connections. 3. Pull push-on terminals from element. 4. On inside of oven, remove two screws and remove old element. 5. Insert contacts end of new element through the holes in oven back wall. 6. Reverse the disassembly steps to complete the installation.

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

Installation instructions on the partsdirect site were great. Unscrewed the (2) hex head screws that hold the element and used clamps to hold the terminal ends from recoiling back into the insulation of the oven cabinet. Put the push on terminal ends on the new element, tightened screws and done. The $50. Part fixed the problem and delayed another range purchase.

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

We emptied the bottom drawer and pulled out the stove, unplugged it and my wonderful son came over and installed the part in about 15 - 20 minutes. The part came without instructions, so we were glad he was around. I am glad we were able to find your service. Thanks.

After reading on the website of others doing repairs I was able to fix my oven easily. I removed the two screws on the back wall of the oven. I carefully pulled the element forward bringing with it the connector wires. Before sliding them off of the old element I made sure that they were pulled out far enough so not to loose them in the insulation. I removed the old element. Slid the connector wires on to the element. Carefully slid the element back into the back of the oven. Put the screws back in and I was done.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

First I turned off the breaker to the oven, then removed the oven racks. I removed the two small bolts that hold the element to the back wall of the oven. I then gently pulled the element out to expose the terminals, with needle nose pliers I carefully removed the clips without letting the wires slip back behind the oven wall. Then I pushed the clips onto the new element and bolted it back onto the oven wall. I turned the breaker back on and preheated the oven and it worked like a charm.

The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.

We've had this range for almost 10 yrs and while on the clean cycle the bake element burned up. We ordered the new bake element on Wednesday and was delivered on Friday. Installation was not difficult as we followed the advice of other installation reviews. However, while removing the old element one of the wires snapped back into the insulation. We had to remove the back cover plate and found the correct wire and just pushed it through. Easy, peasy, japaneasy!

There were no burnt spots on the baking element but I turned the electric power off and removed two screws and removed the two termenals wires and replace them on the new element and replaced the two screws that I removed. I turned the electric back on. Every thing is great and it only took me fifteen minute from start to finish.THANK'S

unscrew element, remove back panel of range. replaced element and reattach connectors. reistall back

followed instructions from the order information sheet.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!