Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E32AR75FPS1

E32AR75FPS1 Electrolux Refrigerator - Overview

Get Parts and Repair Help for E32AR75FPS1

If you know the refrigerator repair part you need, you can browse the list of all parts on the E32AR75FPS1, or you can search by name or part description. You can also find your part by where it is located on the E32AR75FPS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for E32AR75FPS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the E32AR75FPS1

[Viewing 4 of 4]

Manuals & Care Guides for E32AR75FPS1

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.20

LIGHT BULB

$5.96

SCREW-SHOULDER

Sold individually.

$43.38

Evaporator Fan Motor with Wire Harness - 115V

This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator...

$9.58

Adjustable Leveling Foot - Black

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

$73.26

Water Filter Base

$12.72

Air Filter

$37.96

Dairy Door

$27.48

Evaporator Fan Blade

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of plastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

$7.42

Single Gasket Retainer Clip

This genuine OEM freezer gasket retainer clip is used on refrigerator freezers, and connects the inner door panel and door gasket to the outer door panel. The gasket is the rubbery...

$9.22

Tall Bottle Retainer

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice and frost were forming in a frost free freezer

  • Customer: Louise from Ocala, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 50 of 68 people found this instruction helpful
The old gasket was obviously gapping, partially from age and partially from damage during a move. To make the repair, I loosened the screws that are under the gasket and hold it in, but did not remove them. Once all were loose, I removed the old gasket, then starting at the top, ran a thin bead of food grade RTV under the portion of the door that captures ... read more

No water flow to in-door water/ice dispenser

  • Customer: Richard from St. Louis, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 28 people found this instruction helpful
Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet ... read more

Freezer thawing at about 20 degrees

  • Customer: Nathan M. from Bunnell, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 12 people found this instruction helpful
Turned freezer off at themostat and unplugged freezer. Removed 2 screws at front 2 at the back and 2 at the top. Lowered top cover and removed evaporator fan bracket (2 more screws) removed themostat capulary tube( 1 screw and bracket) then unplug fan motor. Removed motor from bracket (2 screws). Put on new fan motor then removed fan blade from old motor ... read more