Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E32AF75FPS0

E32AF75FPS0 Electrolux Freezer - Overview

Get Parts and Repair Help for E32AF75FPS0

If you know the freezer repair part you need, you can browse the list of all parts on the E32AF75FPS0, or you can search by name or part description. You can also find your part by where it is located on the E32AF75FPS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your freezer. We’ve also included any installation videos we have for E32AF75FPS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the E32AF75FPS0

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$97.61

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

Order within the next 10 hrs and your part ships today!
$21.76

Water Inlet Valve

If you notice that the ice maker in your refrigerator is leaking or is not making or dispensing ice, you may need to replace the water inlet valve. When energized, the water inlet valve releases water from the supply line into the ice mold. The water inlet valve is in the back of your refrigerator so you will need to pull the fridge out from the wall before completing this repair. To complete this job, you will need a 1/2 inch wrench, a 1/4 inch nut driver and a utility knife. If your old inlet valve has a screw-in fitting, you may need to simply cut the end of the hose to fit in the new part. Be sure to disconnect both the water and power supply from the refrigerator prior to beginning this repair.

Order within the next 10 hrs and your part ships today!
$8.15

Defrost Thermostat

This refrigerator defrost thermostat is a genuine OEM part and is sourced directly from the manufacturer. Located on the back wall of the freezer section in the refrigerator, the d...

Order within the next 10 hrs and your part ships today!
$103.77

Replacement Ice Maker

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

Order within the next 10 hrs and your part ships today!
$10.94

Fan Blade

This part blows air over the condenser.

Order within the next 10 hrs and your part ships today!
$8.93

LIGHT BULB

Order within the next 10 hrs and your part ships today!
$43.92

Evaporator Fan Motor with Wire Harness - 115V

This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator...

Order within the next 10 hrs and your part ships today!
$28.37

Evaporator Fan Blade

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of plastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

Order within the next 10 hrs and your part ships today!
$6.17

SCREW-SHOULDER

Sold individually.

Order within the next 10 hrs and your part ships today!
$8.82

GEAR

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for needing to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.

Order within the next 10 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken ice maker

  • Customer: Juan from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 176 of 233 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. read more

Ice Maker Stopped Working

  • Customer: JACK from MESA, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 132 of 144 people found this instruction helpful
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only problem was that the ... read more

Broke a blade off of the fan

  • Customer: Milton from Camp Hill, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 60 of 62 people found this instruction helpful
When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair. read more