Models > E23CS78GPS4

E23CS78GPS4 Electrolux Refrigerator - Overview

Get Parts and Repair Help for E23CS78GPS4

If you know the refrigerator repair part you need, you can browse the list of all parts on the E23CS78GPS4, or you can search by name or part description. You can also find your part by where it is located on the E23CS78GPS4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for E23CS78GPS4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.84

Crisper Support

This support can be used for both front and rear and is sold individually.

$2.97

Crisper Cover Support - Front and Rear

This part can be used for either the front or rear support. Sold individually and mounts to the inside cabinet wall.

$60.67

Water Inlet Valve

The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact ice maker mold.

$6.86

Hinge Bearing

Sold individually.

$13.81

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

$23.91

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$100.82

Rear-Mount Ice Maker Assembly

This icemaker mounts to the back panel in the freezer section of the side by side refrigerator. This kit includes the icemaker, power cord, bail arm and fill cup.

$25.71

Dispenser Crusher Housing

This part may look different or be a different color than the original, but will fit and function the same as the original part.

$12.41

Air Filter

$11.66

Ribbon Cable Harness

Used in the dispenser board area.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 121 of 125 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

water leaking out of refrigerator

  • Customer: Jose from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 132 of 161 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in p... read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 102 of 134 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more