E23CS78EPS3 Electrolux Refrigerator - Instructions

This is an easy repair. Unplug appliance. Remove the old water valve by unscrewing it from the frame of the refrigerator. Disconnect the cables and all the water hoses. The hose fittings are a different type: clip off the old connectors from the hose ends and push the hoses straight into the new connectors till they fit solidly. Reconnect the cables and screw the valve back onto the frame of the refrigerator.
Unfortunately, my leak was from a hose, not the valve, so this didn't actually fix it.

Water was leaking so I replaced the entire valve and just followed the color codes and thats it. Plug and play.

I pull out the broken part by push the center pin thru and then rerome all the parts. I then positioned the new part in place and push in the center pin to lock. quick and easy.

Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.

Due to the nature of the support deisign and installation which was unusual I watched the video on how to extract the old broken support and install the new one, odering the new part was simple as the view privided in the parts section was specific and and easy choice to make, cost was very minimal and I received it the next day due to my being in close proximity to the shipping point, thank you and my crisper is very happy and so am I.

it was a simple fix, all i had to do was remove 3 small bolts from top of door, set door aside remove 1 screw that holds door cam in place, install new door cam.hole job took about 15 minute's.

The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.

1-Remove upper plate with phillips screw driver (6) screws 2- remove upper hinge plate with ratchet and socket (2) bolts 3- lift door off bottom cam, lay door flat on floor. 4- Remove broken cam on lower part of door, just pull out. 5- Install new cam in bottom of door 6- raise door up, set on cam, reinstall top bolts and screws 7- p. S. Make sure you trace top hinge location with a pencil before removal, so installation has proper location.

Watched the video and read some comments and from that it was easy

Very easy repair, instruction were clear and easy to follow

Have not really done the repair yet( frig is still to full of Thanksgiving leftovers) but I am sure that with the video that was provided by this site the job will be very simple. Many thanks to the person who put the video together.
John Donnelly

I took the top door plate off lifted up the door and uncrewed the broken part and installed the new one. Lifted the door and placed post into bushing. Viola the door worked better than when it was new

I read other comments and most suggested the fix is less than five minutes and a couple tricks (push the remaining piece into the frig if you can't pull out with pliers)and I did exactly that. Parts came in 2 days, repair took 5 minutes - it took longer to open the package. My wife thinks I'm a star!

Simple, I had a repair man come over and diagnose the problem. After confirming, I ordered the part and replaced it. Need to make sure you get the ice build up out of the fitting tnat goes from the back of the fridge connection at the top and the filler tube inside the unit, mine was iced over. Repair man wanted to charge me $250.00... with his service call and buying the part, it cost $120

took the back off refridgerator, disconnected water valve assembly, then disconnected water lines and electrcal connectors. also i received the part in less than 24 hours