E23CS78EPS1 Electrolux Refrigerator - Instructions

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.

Took door off and installed parts. Video on your Webb site show how to do it. Excellent service on shipping .Had parts in two days. Would use your company again if I had any other problems.

Installed new support. I placed the new one in the hole provided and taped in the locking peg with a small hammer. The total installation took about three minutes thanks to the excellent video provided on the web site. Thanks

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.

Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.

We watched your video online and just followed the instructions. It was super easy to follow and install the new parts. We would highly recommend your site to anyone. The parts came in the mail in 3 days. Thank you very much for saving us to call a repair person and saving us about $100.

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

The part number was easy to find on the diagram. Delivery was as promised. Instructional film was very helpful and reassuring. Only problem was that the broken part left in the door was difficult to remove as it was distorted and would not slide out. Took considerable persuasion by screwdriver and pliers to remove remaining portion. New part went right in and reassembly was easy. Door works fine now.

removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

Remove crisper and shelf. Use a small punch and hammer to gently push the tightening pin through to the wall of refrigerator, keep in mind you'll need to remove this piece with small needle nose pliers before installing new part. Set new part in place and lightly tap the pin in until flush. Install crisper and enjoy the rest of your day.

Remove cover, puch old pin into hole. Remove old support. Set new support in & drive pin in flush. Replace cover.

My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.