Models > E23CS78EPS0 > Instructions

E23CS78EPS0 Electrolux Refrigerator - Instructions

All installation instructions for E23CS78EPS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS78EPS0
46-60 of 266
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

2 broken shelving supports

  • Customer: Victor from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 5 people found this instruction helpful
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

housing-crusher was broken

  • Customer: Bob from Milton WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Ice maker did not produce ice.

  • Customer: william from new port richey FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Water was leaking from the filter area when in-door water dispenser used

  • Customer: Todd from Gotha FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 9 people found this instruction helpful
Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!

Right door makes loud poping sound when open and close

  • Customer: HUNG from CARSON CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

My ice auger would not work.

  • Customer: Dennis from Point Roberts WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
After taking the complete motor, tray, icemaker, etc out and finding no problem, I then finally checked for power at the connector at the top of the icemaker. I concluded that there was no pwoer going to the motor. I then removed the circiut board and found the relay for the auger was not working. Putting the new board in took 10-15 min. and then the auger started to work.

evaporator coil would freeze up solid. no air flow through coil; no cooling.

  • Customer: KEVIN from BRONX NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 16 people found this instruction helpful
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.

Broken Water Dispenser

  • Customer: Scott from Fond du Lac WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I unscrewed the water dispenser and removed the broken piece. Take your time, it is only about 8 screw that need to come out to reach the area for the new part. The only tricky thing about the fix is a spring behind the part. Make sure its lined up, and you should be good to go. Good luck – take your time.

broken shelf support

  • Customer: Richard from West Seneca NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

Plastic water actuator snapped in two.

  • Customer: Alexander from Santa Monica CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
1. Removed exposed screws
2. Removed face plate
3. Disconected wire from switches on face plate
4. Removed screws holding ice/water dispenser
5. Removed screws holding actuator in place
6. Removed wireconnection on actuator (lighted)
7. Replaced broken actuator w/new
8. Replaced all parts in reverse order of removal
9. $300 service call costs me $75 and and 30 minutes of my time. I will always try to fix appliances with the help of PartSelect before calling for service. Thank you!!

Icemaker wouldn't keep making ice

  • Customer: Lisa from Fort Worth TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!

Motor had failed due to ice ejector frozen to tray.

  • Customer: Christopher from Middletown CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.

Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).

Ice make does not fill with water

  • Customer: Amritpal from sacramento CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

Ice tray wouldent fill.

  • Customer: Eric from Greensburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

Ice maker quit working & was over flowing

  • Customer: kenneth from lincoln NE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....
All Instructions for the E23CS78EPS0
46-60 of 266