E23CS78EPS0 Electrolux Refrigerator - Instructions

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

Open box, peal plastic off of glass, slide glass onto shelf brackets

First of all--outstanding delivery time. I chose the cheapest 3 to 5 day delivery and the parts arrived the very next day. The closer plate was a breeze. The hinge bearing was challenging becaue it was broken off flush to the bottom of the door so it took some time with a needle nose plyers to break it into small pieces to remove it from inside the door. Once that was done it was easy replacing the hinge bearing, reassembling the door. Like others have mentioned it took the longest time taking everything off the refrigerator door. Just glad PartsSelect suggested ordering both parts at the same time since I had to replace both of them.

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.

Installed new support. I placed the new one in the hole provided and taped in the locking peg with a small hammer. The total installation took about three minutes thanks to the excellent video provided on the web site. Thanks

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.

Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

Remove crisper and shelf. Use a small punch and hammer to gently push the tightening pin through to the wall of refrigerator, keep in mind you'll need to remove this piece with small needle nose pliers before installing new part. Set new part in place and lightly tap the pin in until flush. Install crisper and enjoy the rest of your day.

Remove cover, puch old pin into hole. Remove old support. Set new support in & drive pin in flush. Replace cover.