Models > E23CS75DSS7 > Instructions

E23CS75DSS7 Electrolux Refrigerator - Instructions

All installation instructions for E23CS75DSS7 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS75DSS7
331-345 of 359
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

light bilb went out

  • Customer: Denise from Landover MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced it

Door closing cam broke

  • Customer: Carol from LENA IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
followed the video instructions and wa-la! Saved my money by not calling the repair man, the shipment of my part was fast, and the repair was even faster. Thank you for helping me in my repairs. Very Satisfied!!! Carol

doors made noise when open and closing

  • Customer: daniel from chesapeake VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the right door. Removed three bolts that hold on the door on. Once removed, I removed the bushing with a screw driver and popped the new one in. Replaced the door and no more noise. Fixed the problem. I also watched a you tube video before I started.

Water was leaking from the glass fill dispenser

  • Customer: DOUG from SPRING TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

Broken Ice Maker

  • Customer: CHERYL from ABINGTON MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was a piece of cake. After a previous day of hours being spent. This was the easiest repair ever. Thank You

Refrigerator freezes everything

  • Customer: MICHELLE from SUMTER SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pretty easy. Removed shelves, removed panel, swapped out part. Unfortunately this did not fix the problem. Still trying to figure out what to do next.

Replaced the water filter

  • Customer: Marvin from Cypress TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the "release button" and took out old filter. Pushed the new filter in place until it 'snapped in place.' Then ran the 'water' until it stopped spitting out air.

replaced water valve

  • Customer: Harold from Goldsboro NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

Broken crisper supports

  • Customer: Kyle from Howe TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video instructions from your site and it couldn't have been easier.

Freezer side kept defrosting

  • Customer: Greg from Camarillo CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After receiving the parts, I clamped on the connector ends, and put on the shrink tubes. Unplug frig, took out the shelves (4) screws, unscrewed back panel (4) screws. Took old thermostat off tube, clipped (2)wires on old thermostat, splice wires, clamped connector on old wires, moved up shrink tubes, and used a heat gun to shrink the wires. Put new thermostat on the tube the old one came off of, put panel, and the shelves back. Pugged frig in. Works great!

water to ice maker

  • Customer: dennis from reserve LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.

drawer frames were broke

  • Customer: Denise from Claremore OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced them with the new ones

crisper support broke off

  • Customer: Denise from Claremore OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

not working due to ice on coils

  • Customer: terry from litchfield IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!

The ice crusher flap was broken.

  • Customer: Mary from Allegany NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.
All Instructions for the E23CS75DSS7
331-345 of 359