E23CS75DSS7 Electrolux Refrigerator - Instructions

I watched the do it yourself video which helped tremendously. My husband was busy so I was able to do it myself.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

Fortunately, this was not hte first time to do a repair on the through the door dispensers. I turned the unit off and removed the door tray (slides out) to expose the screws for trim removal. When that is removed, you remove the circuitry and then remove the actuator and spring. It was difficult to get the new actuator in place. the "stop" which holds it in pace is not forgiviing! And that is being mild. (I remember a few explitive delitives I thought wer gone foreever! I reconnected the circuit to the panel, replaced the panel, and the tricky part was to reinsert the water hose into the dispenser hole. Good luck. When that was in, the entire unit was reeturned with the four screws. The front trim panel was replaced with four screws, and the slide in drip tray was slid in. Job done, and the power was restored. Thank goodness I had some long hemostates to control the reinsertion of the water tube!

took old valve off one peice of it was broke off from freeze replaced it with new valve all but one conection was quick connect electric connections were color coded quick fix works fine thanks Gary

Pushed the "release button" and took out old filter. Pushed the new filter in place until it 'snapped in place.' Then ran the 'water' until it stopped spitting out air.

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

I followed the video instructions from your site and it couldn't have been easier.

After receiving the parts, I clamped on the connector ends, and put on the shrink tubes. Unplug frig, took out the shelves (4) screws, unscrewed back panel (4) screws. Took old thermostat off tube, clipped (2)wires on old thermostat, splice wires, clamped connector on old wires, moved up shrink tubes, and used a heat gun to shrink the wires. Put new thermostat on the tube the old one came off of, put panel, and the shelves back. Pugged frig in. Works great!

electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.

replaced them with the new ones

I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

replaced with kit, very easy unplug unsrew and replace, any one can do it