Models > E23CS75DSS5 > Instructions

E23CS75DSS5 Electrolux Refrigerator - Instructions

All installation instructions for E23CS75DSS5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS75DSS5
61-75 of 416
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My ice auger would not work.

  • Customer: Dennis from Point Roberts WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
After taking the complete motor, tray, icemaker, etc out and finding no problem, I then finally checked for power at the connector at the top of the icemaker. I concluded that there was no pwoer going to the motor. I then removed the circiut board and found the relay for the auger was not working. Putting the new board in took 10-15 min. and then the auger started to work.

Original gate broke at the swivel point

  • Customer: Charles from New Orleans LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 12 people found this instruction helpful
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

Water actuator arm broke

  • Customer: Christopher from Merrick NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
Not too bad, remove the water and ice bezel (3 philips screws) then remove the dispenser unit another 3-4 philips screws. Remove water line from dispenser unit (remember this as the water tube re-insertion is the complicated part) I did not remove anything other then components listed above. Seals and inner door stay intact. Replaceing the actuator and arm was easy. two small philips will free the actuator and arm. Disconnect the two wire harness (black and red) NOTE- there are two sets of black and red wire harnesses that plug in next to each other. One is for the ice dispenser and the other for the water. putting it back together is as easy as taking it apart. However the water line has no play, no slack at all so when reinserting it, the space between the dispenser unit and the door itself is limited. Put the tip of the hose down into the hole you removed it from, hold the dispenser still and use a pair of long needle nose pliers to push (feed) the hose down into the hole. Make sure it comes out the other side by about 1/4 inch to insure it is in and stable. reinstall the unit and bezel. Most of my time was spent feeding the short water tube back in place. You will see just how much room there is between the dispenser and the door before you pull the water tube from the unit. In this case you can judge if it will be too complicated for you before you go any further.

There was a horrendous popping noise when I opened the refrigerator door.

  • Customer: Weston from Anchorage AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
First I cleaned out the side door then, removed the three screws on top of the door. Lifted the door off and set it carefully on a kitchen mat.

I had to use the pliers to remove the existing bearing hinge as it had disintegrated in the door. Once it was out the new hinge slid right into place and I reinstalled the door. I had help with the door. It’s much easier with two people to get proper alignment and to hold it in place while you reattach the screws.

I would have to say the hardest part of this repair was cleaning out the refrigerator.

housing-crusher was broken

  • Customer: Bob from Milton WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
removed ice maker box and disassembled crusher unit on front of box and installed new housing.

No Water or Ice Dispensing

  • Customer: Levi from Ambler PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

broken shelf support

  • Customer: Richard from West Seneca NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

Motor had failed due to ice ejector frozen to tray.

  • Customer: Christopher from Middletown CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.

Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).

door woulg clunk and drop

  • Customer: bruce from eldridge IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
took door off(very easy two bolts on top)lift door replace parts

Ice make does not fill with water

  • Customer: Amritpal from sacramento CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 6 of 9 people found this instruction helpful
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

Right door makes loud poping sound when open and close

  • Customer: HUNG from CARSON CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 9 people found this instruction helpful
I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.

The paddle that dispenses water snapped

  • Customer: Armando from Cumming GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
The part was easy to find on the site, instructions were right on and it only took 25 minutes to accomplish with just a screw driver and a pair of pliers.

door was making a popping noise when you opened the door.

  • Customer: Judy from Visalia CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

Cheap Plastic Water Actuator Broke

  • Customer: Eric from Aberdeen NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Removed Water drip tray, Then removed (3) screws holding the cover in place. Removed (3) more screws holding the circuit board in place. pulled out ribbon cable from the circuit board which is connected to cover, and put aside.
Tried to remove screws holding actuator in place, but it was a bit tight,,wish i would have tried to un-plug the connector on the left side first, but did not, i instead removed the water tube to gain better access,,,,replacing actuator was easy, re-attaching water tube was not simple at all,, but if you do end up pulling it out,,,do not waste time trying to pull it back thru, it is not nessasary, and impossible to do,,the end is tapered, and makes a pressure seal, so it will not leak,,,re-attached screws, ribbon cable, cover, and drip tray,,and done.

Broken Water dispenser

  • Customer: Ellen from Bloomsbury NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
My son and I did it together. I was able to copy and paste the parts diagram on your website and we were able to go step by step following that diagram.We first shut the power to the refrigerator.We then removed the tray and the pad with buttons on the exterior of the fridge. We then unsnapped the electrical plug and were able to tilt the casing that holds the actuator. We removed the old one, and snapped the new one into place.We plugged it in and then proceeded to replace everything. Voila....we now have water again, all for the price of the part...Great!!!
All Instructions for the E23CS75DSS5
61-75 of 416