Models > E23CS75DSS2 > Instructions

E23CS75DSS2 Electrolux Refrigerator - Instructions

All installation instructions for E23CS75DSS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS75DSS2
391-398 of 398
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer leaked, no water disp. & Crusher didnt crush

  • Customer: Edith from Langhorne PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.

Maker would not make ice

  • Customer: Cecil from Blaine WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I suspected that the On/Off Switch was the problem. (Pressing and holding the switch 'on' for 15 seconds to recycle the icemaker did not bring the ice level control arm to life.) I decided to replace the whole icemaker rather than just the switch. (Do not try to replace the switch...almost impossible.) Steps: 1/Remove the Icecream shelf (lift up the front lip and pull out; 2/remove the Icecube holder tray (lift up the front and pull out.) 3/Remove the two hex head screws which are facing you above the ice maker. 4/Pull the icemaker slowly out and and down to reveal the electrical wiring, and unplug the electrical plug. 5/Follow new instructions re the water hopper and the ice-flapper-thingy on the new icemaker, and turn the new switch to 'off' before you start to install it. 6/Plug in the new icemaker, and push the electrical wiring down to the left as you push the icemaker into place, make sure the back edge of the water hopper goes under the water spout. 7/Replace and tighten the two hex head screws. 8/Press and hold the switch 'on' for 15 seconds or more to cycle the icemaker (the ice level control arm will slowly raise up and then go back down). 9/Replace the Tray and the Shelf. 10/Allow the icemaker time to cool and freeze the newly injected water.(This may take up to 6 hours.) 11/Listen for the sweet sound of the dropping icecubes.

water dispenser/ice maker inop

  • Customer: Michael from White Springs FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

support broke

  • Customer: Lisa from Mena AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just put it in the old hole. the hard part was getting the old one out. you have to poke the center piece in to remove. otherwise you will break your fridge. then you have to to pull the center piece out before you put new in.

refrigerator staying to warm

  • Customer: nicole from chipley FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
husband did it took only a few min part was easy to find

water valve leak

  • Customer: Donald from Wilmington NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

broken suport for pam

  • Customer: JORGE from HOUSTON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take of the tray & take parts out & installed the new ones

Refrigerator door "clicked" when opening.

  • Customer: Clinton from Conyers GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed the nuts on top - to loosen the door. Lifted the door off the hinge. Took out old part, put in new one, reinserted door, replaced nuts.
All Instructions for the E23CS75DSS2
391-398 of 398