Models > E23CS75DSS1 > Instructions

E23CS75DSS1 Electrolux Refrigerator - Instructions

All installation instructions for E23CS75DSS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS75DSS1
31-45 of 414
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrig door would not close automatically

  • Customer: Michael from Lithia FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 12 of 12 people found this instruction helpful
Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.

Everything in the fridge was freezing even if it was set on the warmest temperature.

  • Customer: Debra from McRae GA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 24 people found this instruction helpful
I pulled out all the screws and from the freezer side and remove the panel, then I located the thermostat snap the old one out and put the new one in.

The radiator was not defrosting.

  • Customer: Alfredo from Mount Pleasant SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 15 of 22 people found this instruction helpful
The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

Ice Maker overflowing water

  • Customer: Richard from Marco Island FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 13 of 16 people found this instruction helpful
When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 screws. A quick swap with the new ice maker and all is well. Simple

Door would not shut properly

  • Customer: Matthew from Parker CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 11 of 11 people found this instruction helpful
Removed the door and installed ne bushing on bottom of hinge

I had had a repairman look at the problem, and he estimated the cost of the repair to be $225 to $500. Needless to say I was quite happy that I was able to do it myself for $85.

  • Customer: Gary from Floresville TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 17 of 29 people found this instruction helpful
I found that getting the water/ice dispenser back in place was the hardest part because the water hose is so short. I finally threaded a stiff wire up into the hose and guided it through the dispenser opening. The rest was pretty much routine.

Freezer was cold but the fridge was warm. Back panel of fridge was building up frost

  • Customer: Albert from Buffalo Grove IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 17 of 30 people found this instruction helpful
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

drip from door water dispenser

  • Customer: Paul from Anderson IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 11 of 13 people found this instruction helpful
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

ICE MAKER DOESN'T MAKE ICE

  • Customer: JANET from NEW FAIRFIELD CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 25 people found this instruction helpful
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

GLASS SHELF BROKEN

  • Customer: ROBERT from DOYLESTOWN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 22 people found this instruction helpful
SIMPLY SLID GLASS INTO FRAME & IT FIT PERFECTLY.

Cheap plastic part.

  • Customer: Erin from Gresham OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 17 people found this instruction helpful
Pulled the drip tray out of the ice/water dispenser.
Removed 3 screws, pulled up the beauty ring.
Removed 3 more screws, pulled out the circuit board, and plastic plate that it is installed in.
Removed screws that hold the actuator in place. Unplugged and removed broken actuator, installed new actuator, installed hold down screws. Plugged in actuator. Installed beauty and other parts in reverse of removal. Would probably recommend removing door handle on the dispenser side. Would make installing one of the screws much easier. But you have to remove 2 small hex screws to remove handle.

2 broken shelving supports

  • Customer: Victor from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 9 of 9 people found this instruction helpful
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

IT WAS FAST AND EASY, NO TO MENTION AFFORDABLE.

  • Customer: Jim from Herington KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 9 people found this instruction helpful
REMOVED THE TWO SCREWS THAT HOLD THE ELEMENT IN PLACE. THEN I PULLED THE ELEMENT OUT ABOUT 3 INCHES AND DISCONNECTED THE WIRES. EVERYTHING MATCHED UP PERFECTLY.

Ice Maker wasn't making ice

  • Customer: Robert from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 10 of 13 people found this instruction helpful
I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

Ice maker did not produce ice.

  • Customer: william from new port richey FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 11 people found this instruction helpful
The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill
All Instructions for the E23CS75DSS1
31-45 of 414