E23BC68JSS2 Electrolux Refrigerator - Instructions

My grandson did it and only took a few minutes.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

Not long after we bought this fridge, the plastic on the light switch cracked, making the lever stick out too much so that the door wouldn't close. It's been taped down ever since. I simply pulled the old switch out and plugged the new one in. I'm kicking myself that I didn't do this ages ago. It was so easy and now I can see inside my refrigerator again.

Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

Unplugged frig. removed old switch with the aid of screw driver. removed wires and taped; plugged frig. back in and waited for new one. new one came, unplugged frig.removed tape from wire clips plugged in to switch and pushed switch into socket hole and plugged frig. back in; shut door, works like a new one.

I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy

Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.

Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!