E23BC68JPS3 Electrolux Refrigerator - Instructions

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!

I put the new unit up to the old one to see exactly how it goes, took the 2 screws holding the unt off...Took the 3 water lines off with adjustable wrench, put back exactly the same way and it worked with no leaks

Write down where tubing goes, wiring is color coded.

carefully removed retainer from old valve

The u tube instructions were exactly what is needed. I had to cut off the old plastic pipes. My pipe had threaded connectors. Pex push on connection is super easy. You don't really need a block of wood to cut it if you have a sharp utility blade. If if you are sure this is the problem this is a really easy fix. Steps 1 turn off water at wall unplug electric also 2. Disc line at valve on refrigerator 3. Remove 2 screws holding valve 4. Pull valve out and remove plastic hoses and electric connections pay attention to color of pipe and electric connection. Mine were color coded. Had to cut off thread connectors. Reattach in reverse order or do one at a time. Check for leaks.

Undo a few bolts unplug power and unhook water lines then recut all lines and push in to new value

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.

We replaced the damper, but it didn't fix the problem. We then purchased and replaced the thermistor. (We had previously replaced the defrost thermostat). The refrigerator side is now cooling better, but not enough. The damper doesn't seem to be opening. So we have now unplugged the damper and left the opening between the refrigerator propped open and the refrigerator side is now cool enough. (We had previously tried keeping the damper open before we replaced the thermistor and the refrigerator didn't cool off. So the thermistor did fix something, but the damper doesn't seem to have been the problem).

Easy repair. Great part. The hardest part was removing the fridge lower exterior door so I could get access to the icemaker. A couple of youtube videos later I realized loosen a screw, slide the icemaker out and unplug slide the new icemaker in and plug-in making sure the water spout was accurately over the water receptacle for the icemaker. Several hours later I was up to my eyeballs in beautiful clear ice cubes. Highly recommend.

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

My grandson did it and only took a few minutes.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)