Models > DWUA451AAB > Instructions

DWUA451AAB Admiral Dishwasher - Instructions

All installation instructions for DWUA451AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DWUA451AAB
31-45 of 452
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

spray arm would not stay on during wash

  • Customer: Alane from Piedmont OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 9 people found this instruction helpful
Removed old spray arm and spray arm nut with a twist of my fingers. Screwed in new spray nut with my hand, and snapped in the new spray arm. Works PERFECTLY! I did it all by myself! Saved me a costly plumber bill! I am soooo proud of myself!

heating element split open

  • Customer: Hadley from De Leon TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 9 people found this instruction helpful
I took the bottom cover off and pulled off 2 wires and removed 2 plastic nuts. I removed the old part and removed the O rings from the old part and installed the new heating element. Replaced the plastic nuts and the two wires. It was very simple. The hardest part was lying on my back to get to the wires and nuts.

Pump gasket had deteriorated with age and causing odors.

  • Customer: Kenneth from Brooks GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 9 people found this instruction helpful
The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

Leaking

  • Customer: L W from Manning SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 10 people found this instruction helpful
I first changed the dispenser door latch grommet, which was very eazy except for the left side nut screw which was a little awkwaed to get to with the nut driver. Not a big problem but difficult enough that i stripped the threads (plastic) and had to get a larger screw which is working fine so far. Since the grommet didn't stop the leaking although it was obvious it was leaking from the soap trail. I ordered the gasket and got it very promptly put it on and guess what. Still leaked some. I discovered when they installed the dishwasher the door appeared to be warped. To fix this there are two door tension springs under the bottom panel. By adjusting these with a log screw driver problem finally solved.
It is good to have not only a great place to get parts but the idea's from others are terrific. Although this washer is 15 years old it looks new and now acts new. Thanks so much for good service and advise.

Maytag dishwasher was leaking from front, bottom right corner

  • Customer: Mike from Fairfax VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
We simply removed the old gasket which was corroded, cleaned up the hard water buildup, and popped the new gasket into place. The problem was fixed! No more leak!

the lifter broke so the washer would not hold water.

  • Customer: gary from webster TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
had to remove the spray nozle and cover from the bottom of the washer to expose the stem where the lifter mounts. I had to turn the stem slightly to install it, this had to be done from the bottom of the washer and it took an extra set of hands. Once the stem was in the right position the lifter slid right on, I attached the retainer ring and put the othe parts back on. It works as good as new now.

Dishwasher door was crashing open

  • Customer: Bill from Morganville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 7 of 7 people found this instruction helpful
The replacement of the spring linkage was simple - the pulling out and pushing in of the under-the-counter dishwasher was the difficult and time-consuming part. The repair of the part took less than a minute.

The actual repair -
1. Hook the linkage to the dishwasher door
2. Hook the spring to the dishwasher base
3. Hook the spring to the linkage.

Getting the dishwasher out to be able to make the repair involved:
1. Unscrewing the base panel (6 screws had to be removed)
2. Unscrewing the dishwasher from the counter (two screws)
3. Turning off the water supply
4. Disconnecting the inline water supply from the dishwasher.

Once the part was replaced, I had to return the dishwasher to its original position, which meant performing the four steps (in reverse) used to pull out the dishwasher.

water leak through door

  • Customer: marvis from barbourville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 7 people found this instruction helpful
1- turn power off. 2- remove 7 screws to take door apart 3- remove 2 screws to take dispenser out. 4- i unhooked electic plug from it. 5- replace grommet and all back together. not bad to be 72 years old.

Leaks on floor in front of washer.

  • Customer: Jim from Yorba Linda CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
Removed two lower panels using nutdriver. Ran washer through a rinse cycle, to determine for sure where leak was coming from (under door on left). Examined the door gasket and observed buildup of lime deposits and a general depression of the gasket through years of use, especially in lower portions. Removed the old gasket observing how installed. Cleaned out groove with Lime-away and toothbrush. Washed clean using water in a squirt bottle. Dried things out using paper towels, and then pressed new gasket into place, starting at lower left. Readjusted the gasket to fit precisely end to end. Shut door and ran a drip free load.

The detergent cup cover would not open and the rinse aid was not dispensing properly

  • Customer: Timothy from Northville MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
I removed the seven screws from the back panel of the door (special tool) and seperated the back panel from the front. My wife held the back up and I removed the two wax motors (detergent cup and rinse aid), which were clipped in place. I had turned off power to the dishwasher, so I simply unplugged each wax motor from the wiring harness, plugged the wax motors in and clipped them in place, making sure that the wiring harness was put back in the same place. Then I put the back panel back on the door, turned the power on and tested the repair. The dishwasher worked perfectly. Thanks to PartSelect for helping me solve the problem. The parts arrived in two days!

dishwasher leaked

  • Customer: Jean from Gaffney SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

Broken door spring linage and lost spring

  • Customer: David from Mesa AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Took off bottom plate for access. Slid part that holds bottom of spring forward so I could reach it without pulling dishwasher out of position. Hooked spring to bottom attachment, then connected door spring linkage to holder that is attached to the dishwasher frame. Adjusted the tension with the tension screw and buttoned up bottom plate.

leaking door

  • Customer: VIOLA from BOUCKVILLE NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Removed the old gasket, without tools, and fit the new gasket into the space, making sure it was in the groove correctly all around, job done, works great. The ordering of the gasket on this site was easy and the shipping time was amazing, one day. Would use this company again, and recommend to anyone needing parts that wants to do repairs themself. I am sure saved a whole lot over hiring someone, and got the job done sooner also.

leak through impeller seal.

  • Customer: Maxim from Ashburn VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 7 of 8 people found this instruction helpful
removed spray head, pulled motor/pump assembly. took apart impeller housing and then removed motor and pulled impeller off its shaft, the most difficult part was actually pulling off impeller from the splined shaft. I actually broke old impeller in the process. The good thing is that the new seal came assembled with new impeller so that was not a problem. After re-assembling everything it worked fine and still works for a week since repair.

Leaking water from the discharge hose and pump gasket

  • Customer: Roger from Palm Bay FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 11 people found this instruction helpful
1) Remove the lower dish rack.
2) Use towel to soak up any water in the dishwasher.
3) Remove the bottom plate on the dishwasher front.
4) Remove clamp from around the discharge hose. Some water will drain out so have towel handy.
5) Dishwasher will need to be pulled out from its built-in area in order to feed the old discharge hose out and the new one in. MAKE SURE THAT THERE IS ENOUGH PLAY IN THE ELECTRICAL WIRES AND THE INPUT WATER LINE TO THE DISHWASHER TO ALLOW IT TO BE PULLED OUT.
6) Loosen, all the way, the white plastic locking arm that clamps the pump housing. It clamps on a white corrugated plastic piece.
7) Remove the spindle arm inside the washer by unscrewing the "tower" piece.
8) Remove the screws from the pump housing on the inside of the washer.
9) Lift the pump housing carefully and remove the rubber gasket from around the housing. There is enough play to remove the gasket and put the new one on.
10) Clean the area around the housing so that the new gasket seats properly.
11) The new gasket will have to be installed before re-installing the discharge hose.
12) Re-install screws in pump housing.
13) Re-install the spindle arm.
14) Tighten the white plastic locking arm underneath the washer that locks down the pump housing.
15) The new discharge hose can now be reconnected between the sink drain and the dishwasher.
16) Dishwasher can now be put back into its place.
17) Before closing up the bottom plate of the dishwasher, it should be run and checked for leaks before finally closing up. My advice - let it stand overnight before checking for leaks. after running.
All Instructions for the DWUA451AAB
31-45 of 452