DWD1500AWW Admiral Dishwasher - Instructions

1- replaced accumulator filter and docking station with flappers, the docking station with flappers may not have been necessary? But what the heck, if your into it this far why not. Check out the tech. Video it was helpful. The dishwasher works like new now. 2- the door latch switch was worn out, to replace this part I first unplugged the power cord then removed the 8 screws from the inner panel of the door exposing the door latch assembly. Unplugged the two connectors and installed the new part and reassembled everything, pretty easy! The dishwasher works like new now, and for around $ 102.00 bucks, saved lots of money doing it myself, thank you Parts Select for your help. Carlos, Lancaster, California.

The door latch to our dishwasher was broken. Removed the screws and latch assembly came right out. Needed to purchase entire assembly and assembly was just as easy as removing. Installed and gave it a test drive and it works great.

Replaced The part. Picked up the old one and repurposed it in the work shop and dropped in the new one ...no tools needed. The real story here is that this web page existed and I was able to get the exact replacement part I needed delivered to my house.Piece of cake,

Replaced silverware basket. Works as designed. Speedy part delivery and great service!

easy repair

Unscrewed inside cover relaced unit reolaced inside cover

unscrewed cover panel, lifted out latch assembly w/ switches,unplugged old switch. plugged in new switch and replaced panel.

Replaced electronic control board burned out. Service representative was extremely helpful. All husband did was check power, shut it off, took out old electronic control board and put in new and replaced screws. Working like a charm.

I first ran a cycle of clear glass to verify that there was something wrong. I pulled an exploded parts diagram off the internet to see what parts there were and to give me an idea how everything came apart. I slowly took piece by piece< keeping all screws seperated with the part they belonged with. I set the parts in the order they came out so I knew what way they would have to be returned to the machine. I cleaned and inspected all parts to ensure they were in working order. When I removed the accumulator filter I noticed all the screens were caked with what appeared to be soap scum. I then noticed one of the screens was tore away from the filters body about a half inch long. I decided to order the part(which was a sunday). The part was on my door step by tuesday morning( with standard shipping). I had the part reinstalled in 10 minutes. The hardest part of the whole job was getting all the slats on the filter to line up with the ones on the cover to be screwed onto it. They need to be lined up or the screws will not go in properly, which would be a whole different bag of worms. The job was seriously simple and the ease of ordering and receiving the part made it that much better. Thank you for being a great service to the service industry.

took off drain hose pulled out flapper on the pump side and installed new one then put everything back together

This was so simple. I took the screws out with the Torx Bit. This allows you to open the inside of the door. You'll see the wires and the back of the handle. **Be Sure to note which side the wires hook up to. I wasn't paying enough attention and had to figure out where the black and the white wires went after the fact.** Then, simply remove entire "T" shaped handle assembly. The new assembly comes with white wire covers with black backs, shaped like a rectangle. There are two prongs on each that need to be squeezed and gently rocked back and forth- not enough to break them- until it pops off. Then replace with the white. Replace with new. ** The handle will NOT line up on the outside until the entire proess is done, and you close the door so don't waste your time trying to figure out why!** Replace screws around the interior door and close. Easy breezy, it only took about 15 minutes, including time to run to the tool box a couple times.

I used 2 foam insulation strips; one on top of each other-now no more leaks.

very simple. I unscrewed the plastic surface of the dishwasher door, took out the old foam pad and put in the new one. It stopped the leak. A very inexpensive and very simple way to fix the problem.

just snapped the wheels on. It took less than 10 minutes.

Used a phillips head screwdriver and removed all of the screws on the inside of the door. Once I removed the panel the latch was free and I use the pliers to unplug the wires. I put the wires on the new handle and latch assembly, put it back in place, put the panel back and screwed it back down. Piece of cake ,only took about 5 to 10 minutes.