Models > DWB1000AWX > Instructions

DWB1000AWX Admiral Dishwasher - Instructions

All installation instructions for DWB1000AWX parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DWB1000AWX
451-465 of 473
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grinding noise and dishes not getting clean

  • Customer: David from Trussville AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Upon removing parts in an easy systematic order I discovered glass in the bottom of the machine. Was able to remove all but the Wash Impeller. This seemed to be stuck and I could not unscrew even when holding the impeller with pliers. Finally broke it. Ordered a new impeller and installed a few days later and everything works like new. Total cost less than $20. Wife is happy - I'm happy. Washing dishes by hand for a few days reminds you of how much we take modern appliances for granted. Oh - by the way. Very happy with the PartSelect service.

Removing the spray attachment

  • Customer: John from Naples FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Had to figure out how to remove the spray attachment and assemble it into the replacement dishrack.

RUST AND DETIORATION OF DISHRACK

  • Customer: Marilyn from Nebraska City NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I read the other persons who did the same job to find out how to remove and replace the tower on the lower rack. Then just lifted out the old one and replaced it with the new one after attaching tower and replacing silverware tray. I have ordered parts from PARTS SELECT in the past, and have never had a problem. THANK YOU

Snap retainer broke.

  • Customer: Garth from krakow WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new one. Put it in.

Dishwasher had begun to leak around lower part of door

  • Customer: Raymond L from Rockville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old door gasket by pinching it and slowly pulling it out of its track. Used a small headed bristle brush to clean any remaining rubber particles from the old gasket to insure a clean track. Carefully placed the new gasket in place starting at the left bottom corner and working around the track to the bottom right corner. Perfect fit . . . no leaks.

The upper spray arm kept falling off.

  • Customer: MONA from HOUSTON PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I replaced the spray arm snap retainer,but the problem still exists. Do you have any suggestions?

The filter had become brittle and needed replacement.

  • Customer: Harry from Canyon Lake TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed the bottom rack and the lower spray arm. With a star point screw driver removed 6 screws to take off pump housing. Lifted out the old filter. carefully bent the new filter (shipped flat) into a circle and connected end clips. Replaced bottom edge of filter into groove. Replaced pump housing and spray arm. Back in business!

Door seal leaking

  • Customer: Bo from Madison AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replacing the door seal fixed the leakage problem I am very happy with the fix and I installed it myself.

Water leak do to freezeing, the solnoid cracked.

  • Customer: Robert from Morley MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The part is on the bottom of the washer. You have to remove the front panel at bottom (four screws)The part is on the left side of the washer. First thing to do is to remove the water inlet hose, using an open end wrench. There are two screws that hold the part to the sideof the washer. I used a multibit screwdriver with no bits in it, it the right size and works very good. Disconnet the electic from the part. Turn part so you can the see outlet hose & clamp, use a pair of plyers to open and slide the clamp up the hose, and pull the hose off the part. To reassmble reverse the procedure.To show how easy this is I'am a 76 year old man and had no trouble at all. The hardest part of the job was finding the leak in the first place

Leaking

  • Customer: Brian from Collierville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
COULDN'T FIND THE PART AT ANY HARDWARE STORE OR BAX STORE. BOUGHT 3 DIFERENT HOSES BEFORE I FOUND THE RIGHT ONE ON LINE WITH YOU.

Leakage from the front of the door

  • Customer: Matthew from Pemberton MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using the information from this site on what could cause the problem, I ordered the door gasket and the detergent grommet. Silly to do the door gasket, which helped slow down the leak but didn't fix all of it, and then have to go and order the grommet and wait for that to show up when it is less than $5. I need of a door gasket really bad anyway. I peeled the old door gasket out with a screw driver and replaced the new one in less than 5 minutes. Test ran the dishwasher and found that it still leaked some. Removed the inner door panel as shown in the help video, 7 hex screws, very simple, no suprise pieces falling out, removed the detergent latch, (2) 1/4" screws, and slide out the piece. The grommet was almost gone. Slipped the new one on, replacing all the pieces the way they came off and test ran again. One little drip but I think it left over moisture from before. Have it twice since with no leaks. Perfect solution.

Broken door latch

  • Customer: john from Little Rock AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Ordered part with simple instruction.

rusted lower rack

  • Customer: Margaret from Bellingham WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed rack but had trouble removing the tower and didn't find any help in your video...finally just twisted it out.

original rack was damage

  • Customer: Maria from Wanaque NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the replacement was easy, just have to pull the water jet out and attach to the new rack.

Did not spin and dishes dirty

  • Customer: William from Kirtland OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
First I took apart and went to local appliance store. The wash impeller was broke for sure, but I could not figure how it worked. Their diagrams were not accurate and they only sold a kit for $40 just to get the wash impeller. I went online and found your site. I also could tell by your diagram(which was accurate) that the discharge pump housing was broke also. I found this on your site since it was under the problem I was having. I ordered the parts from you for $32 with shipping (included wash impeller and discharge pump housing). I received the parts on the second day, watched the video, and put back together. It works excellent. I am very impressed and will use your site for anything that breaks, and tell everyone about it. Thanks
All Instructions for the DWB1000AWX
451-465 of 473