Models > DWB1000AWE > Instructions

DWB1000AWE Admiral Dishwasher - Instructions

All installation instructions for DWB1000AWE parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DWB1000AWE
451-465 of 470
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher leaking from door

  • Customer: Marlon from Hamilton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered parts on Saturday, and they arrived Tuesday. Followed the instructions in the video. It could not be easier. I may turn pro when I retire.

motor running - no spray

  • Customer: Richard from Springfield MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed racks - removed lower wash arm - removed filter screen - removed upper pump cover - removed broken wash impeller - replaced wash impeller - re-installed upper pump cover - re-installed filter screen - re-installed lower wash arm - re-installed racks

The gasket is press fit in a channel around the door

  • Customer: Roy from Shoreline WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Orient the gasket so that the more squishable hollow side of the gasket faces the door, and check that the length is sufficient to fill ths entire channel. The less compressible side goes into the channel, which requires some skill and strength to seat well. The flat portion of the more or less square gasket has two edges to it. What works best is to put the edge that is toward the inside of the dishwasher into the channel with your fingers, and then press in the other edge firmly with the small spatula of about 2 or 2and 1/2 inches until you can no longer see that edge. This is the visual indication it is seated. in the corners you may only be able to use a corner of the spatula.

pump disintegrated

  • Customer: James from St Helens OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding the part cheaper on your website and watch you video it was a peice of cake. and the pump only took like 4 days to get here during the holidays. Jim

water leak from between the inner and outer door panels

  • Customer: Troy from Nashville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Installed a new grommet on the soap door latch. Replaced door seal at customer request. The door seal ordered was to short. Replaced door spring clips at customer request. Split the door, remove 2 screws from inside the inner panel, grommet is between the inner panel and latch mechanism. Line the new grommet before install.

door the soap dispenser stopped opening

  • Customer: steve from dummerston VT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
unscrewed 7 torx screws with the impact driver. removed the motor from the bracket. comes out pretty easily. moved wires aside. Pulled the wires off the motor using the pliers- one came off very hard, note where they go, corroded in place. installed the new motor by easily re-attaching the leads. Biggest surprise was that there were 2 motors. I initially replaced the lower one which did not solve the problem. When I replaced the upper, it worked. Not sure of the function of the lower motor. The upper one clearly fits into a slot which seems to attach to the doors.

Unit was making a grinding noise when pumping out water

  • Customer: Steve from Kenner LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Opened lower panel to better locate noise ( ran in drain mode to pinpoint ). Removed lower tray & started taking apart , found the discharge pump housing had broken on the inside. Ordered parts , they came in a few days & put back together. All works fine & it runs quieter than before it broke

injector seal ring was leaking

  • Customer: James from San Marcos TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
simply replaced the ring and the water inlet injector, no tools need on that part of the repair

Door Spring linkage broke.... replaced

  • Customer: Vicki from Spokane WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Go to computer, log onto PartSelect, order part. Two days later, go to mailbox, open package. Go back to computer, log onto PartSelect, watch instructional video on how to install the part. Go to kitchen, do what the video showed you to do. Job done.

Lint screen would not clean well

  • Customer: Amanda D. from Flag Pond TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced lint screen.

leak @ bottom of door

  • Customer: Ron from Westwood NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First replaced the door seal, that slowed it down substantially, but not totally. Next replaced inner door foam insulation strip and that took care of it, no more leaks. There was some corrosion evident after I scraped off the old strip, sanded that smooth with emery sandpaper and then installed new strip. Job done!

Spray arm fell out of top of washer because retainer had failed.

  • Customer: James from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Watched on site video. Very helpful as it explained how to remove the upper and lower baskets to get at the upper cabinet nut. How to remove the nut and use a socket to compress the retainer rams so they would pass easily through the hole in the spray arm. Retainer nut replacement 1 minute. Removing and replacing baskets in machine another 5 to 10 minutes.

Plastic linkage had broken

  • Customer: Sandy from Grass Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed the outstanding video instructions. Your company is fantastic. Your attention to detail, the quick shipment (one day) and video ... stellar! We will be referring your company to all!!! Thank you!!!!

water leaked out of door.

  • Customer: Robin from Levittown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced with new gasket and it works great.

Water leaking form left front of door.

  • Customer: Richard from Manitowoc WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the parts within two days. Watched the video and it explained everything. Found it hard to believe how easy it would be, and it was very easy. Cleaning up the door in preparation to installing the new gasket took longer than the gasket installation. The gasket just pressed in the channel, frankly I was surprised that the door inner shield did not have to be removed. The water deflector just pulled off and slipped on (probably took 30 secends. Ran the dishwasher a few times, and no leaks. They had cited that the majority of leaks were due to the gasket, and it was right on. Like the dishwasher and can go for another 12 years.
All Instructions for the DWB1000AWE
451-465 of 470