DW860UQP Jenn-Air Dishwasher - Instructions

1. Turned power to the unit off.
2. Used a star bit to remove the 7 screws holding the door panel in place.
3. Handed each to my 2 year-old grand daughter.
4. Removed a 1" switch metal retaining plate and a black plastic cover. Removed one screw holding the switch in place.
5. Gently lifted out the old switch and compared it to the replacement switch.
6. Inserted the two black connectors into the new switch.
7. Removed each of the four wires connected to the old switch and connected each, in-turn, to the new switch. Removed the exterior black handle from the old switch and snapped it into place on the new switch.
8. Put the switch into place, reinstalled the black plastic housing cover and long 1" metal switch retaining panel.
9. Set the door cover in place and let the 2 year-old screw in the 7 retaining screws.
10. Don't have to listen to the wife complain about the dishwasher anymore.

First, removed end cap in steel sliding upper rail, second, removed broken roller, third, attached new roller, you can look at other rollers to see how it goes on, fourth, feed new roller into track, replace end cap. Takes less than 10 min, saved 85. 00 Bucks.

Took off old part. Modified new roller w'knife. Found a nut and bolt in scrap pile. Attached.

The wax motor seemed to work.
At first I thought something was broken and I tried to figure out the "theory of operation" Working the actuator of the wax motor, I COULD NOT GE THE LATCH TO MOVE THE WAY I THOUGHT IT SHOULD. I ASSUMED EITHER IT WAS BROKEN IN SOME WAY I COULD NOT DETECT OR THERE WAS A FLAW IN ITS DESIGN!

It took a long time to figure out the latch would not be worked open unless it was actually holding the lid- this positions the latch at "half mast" and allows the mechanism to "pick it up from there" and open the rest of the way. So once I figured that out, I concluded the failure was really just worn out parts that were out of tolerance for how this "half mast" position and opening was supposed to work. So I ordered all fresh pieces just to be sure, assembled it (very easy) and put it in (easy). It all works fine now.

First I called a repairman. He saw it was a certain model Maytag and would not fix it. It washed, but would not drain, so rather than buy another I took about an hour to carefully remove the washer and the motor / bowl unit from the body. Then it was easy to see what was wrong. The problem was a broken lifter arm in the bottom of the bowl. This caused the drain solenoid piston to "travel" too far and actually dislodge from the solenoid during use. You have to remove the lower spray arm, drain grate and then the lifter is a little black plastic "arm" on a metal rod that is actuated by the solenoid under the washer. The lifter fits over the rod and is held with a snap ring. Re-assembly was easy.

Whoever manufactures this part, hope they read this and strenthen this part. The very thin legs break very easily.

I removed the threaded broken-off part from the extension thing. The spay arm came off, since nothing was holding it on any more. I pried the cover off below that - 4 tangs.
Then I used needle nose pliers to unto the strange pointed nut that holds the spray arm support in place. Then removed the borken support, replaced with the new and reassembled in the reverse order of disassembly. Really pretty easy.

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

After performing some maintenance to get the water flowing properly through the system (that's another story) the door was leaking very badly during any test run of the dishwasher.

We thought it was the gasket because the old one was calcified and dried out from years of harder water.

We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.

I simply ordered new rack assembly for the upper and lower rack units. Removed the old racks and slid in the new ones. I gotta say, Part Select saved me $50 for these racks compared to everywhere else I looked and called.

Thank you Part Select !!!

I removed the screws on the inside of the door. Removed the cover and changed door switch and holder and put the new one in. Replaced the cover
all in less than half an hour.

The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

Suspecting the problem was a sticky gasket on the old detergent cup lid, I replaced the lid.
First remove the old lid by pushing one of the hinge pins (the one without a spring) out of the cylinder hole in the dishwasher door. Important: before completely removing the lid, note how the spring is installed on the other pin. Then, simply install the new lid and spring and push the non-spring pin back into the cylinder hole in the DW door.
My dishwasher now works fine! :-)

I was able to remove the old handle and place it on the new basket - using only a screw driver.

had to remove the spray nozle and cover from the bottom of the washer to expose the stem where the lifter mounts. I had to turn the stem slightly to install it, this had to be done from the bottom of the washer and it took an extra set of hands. Once the stem was in the right position the lifter slid right on, I attached the retainer ring and put the othe parts back on. It works as good as new now.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.