Models > DW860UQB > Instructions

DW860UQB Jenn-Air Dishwasher - Instructions

All installation instructions for DW860UQB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DW860UQB
1-15 of 520
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water dripping from right corner of door

  • Customer: Tim from Ringgold GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 484 of 487 people found this instruction helpful
Took out about 7 torx screws to remove the inner door liner. Discovered evidence of leak coming from the sop dispenser latch, and noticed the grommet had turned soft and was torn. The grommet is only about 1" square. Used nut driver to remove two screws to remove latch assembly. Slipped old grommet off and put new one on, and reattached the latch. The foam seal at the bottom of the door looked worn, so we replaced it with weatherstripping from home improvement store. The main door seal was brittle, so we replaced it too - just grab an end and pull the old one out. The new one was installed by starting at one end and we just pushed it in place. We used a nut-driver to push it in - we were afraid a screwdriver might damage it. The new door seal required us to latch the door to get it to stay closed the fist couple of days, but now it has loosened up a bit and works as expected. And NO MORE LEAKS. Cost is much less than a new unit!

bottom rack needed replacing

  • Customer: Cheryl from South Burlington VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 469 of 476 people found this instruction helpful
Just took it out of the box and slid it in.
Only problem I encountered, and I think it was due to the age of the dishwasher, was the newunit was not as deep as teh original rack. This will require a new method of loading dishes. Also, the new basket doesn't really fit well in the new rack.
Still cheaper than replacing a good cleaning dishwasher!

Rack roller broke

  • Customer: Kathy from Lombard IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 461 of 462 people found this instruction helpful
I opened the end stop of the rack, replaced the roller, and put the end stop back on. I can't believe I paid the repairman the last time $125????? An he put in a regular screw that rusted and broke the roller. Took me 3 minutes! Thanks

The utensil basket was old, bowed and the bottom was falling out.

  • Customer: Janet from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 384 of 388 people found this instruction helpful
I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.

The dishwasher roller axle needed to be repaired

  • Customer: Rosemary from Toms River NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 364 of 366 people found this instruction helpful
I watched the installlation video found on the wedsite and followed his directions.

Maytag makes a really crappy silverware basket. The bottom of ours fell apart the first year.

  • Customer: Kenneth from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 135 of 202 people found this instruction helpful
There was no repair to be done. Just replaced the defective basket with the new one.
I got the part two days after ordering it. Great service.

The bottom of our dishwasher's old utinsel basket broke out

  • Customer: Wade from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 98 of 99 people found this instruction helpful
It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.

I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.

Dishwasher was leaking in the lower left hand corner from time to time.

  • Customer: Dina from Hammonton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 83 of 83 people found this instruction helpful
Using the pliers, my husband pulled out the old gasket to get it started. He then pushed the new gasket in with his fingers and used a screwdriver to press in the ends. That's it. Pretty easy. I ran the dishwasher a couple of hours after he installed it and there were no leaks. Still not leaking. Seems a bit quieter since the seal
is better.

I was secretly hoping for a new dishwasher eventually. But it makes much more sense to shell out $43 for the gasket rather than spend the $600 or better for a new dishwasher!

I found the website very easy to use as well. Everything shipped quickly and there were no problems at all. I will bookmark this in favorites should I need it again!

Water leaking below door

  • Customer: Jeff from Sandy UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 104 of 168 people found this instruction helpful
I originally thought the door gasket was leaking so I went to partselect on line to order the gasket. After seeing the repair story results, I also decided to order the soap dispenser grommet also. I first relaced the door gasket as that takes about 5 minutes (take the easy way first right,) I was wrong as it still leaked. I then took the 7 torx head screws off from the door and the inside section just lifts off exposing the underside and the real problem. The soap latch had been leaking and was obvious from the dried soap/water trail. You have to remove two small screws and the whole unit comes out very simply. I took the extra time to clean off the build up of soap and hard water before replacing the seal and remounting the soap dispensing latch assembly. Ran another load and no more leaks! Thanks for the advise and the really simple but accurate way to order parts. I will use this site if I ever need any other parts. Very helpful and quick deliver as well as reasonably priced.

Dishwasher leaked from lower door area

  • Customer: Michael from Grand Rapids MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 94 of 155 people found this instruction helpful
Observed the way gasket was installed including slight overhang on each side.
I simply pulled out the old gasket, starting at one end. I then wiped down the area with a dampened rag and pressed in the new gasket exactly the way the old one came out. It is important not to stretch it, just push it into place ending up with the same overhang on both sides.
Total time less than 5 minutes with no tools.

worn out silverware basket

  • Customer: Dayna from Logan UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 95 of 158 people found this instruction helpful
Ordered replacement basket online at much better price than available localy. When I recieved it discovered that it did not include the handle, but was suprised to see it labeled as "Genuine Maytag Parts" ( I realy expected a knock-off replacement part for the price difference). I was able to remove tha handle from the old basket and install it on the new one. Job done. No problem

Roller disconnected from upper rack, due to a cracked clip

  • Customer: Bernard from Boulder CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 89 of 151 people found this instruction helpful
Once I figured out how to get the endcap off the roller track (allow several minutes, because it was designed by some dork), I slipped the old roller off the track, put the new roller on, and clipped it to the rack. Then I put the track cap back on (really easy once you've figured out how to get it off) and it was good as new.

As for how the cap comes off, it's difficult to describe. But it may help you to know that the cap, despite what it looks like at first, is actually surprisingly long and folded on top of itself. Pulling it directly out doesn't work; you have to unfold it before there's any chance of getting it out.

dishwasher door leaks

  • Customer: jerry from vernon CT
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 59 of 63 people found this instruction helpful
I ordered and replaced both the door gasket (easy) and inner door seal (difficult) to try and correct a leak during operation. The door gasket was easily replaced. However, the inner door seal was a bit more trouble. After removing the inner door I found that the old inner seal needed to be removed and surfaces thoroughly cleaned of old build-up of dishwasher soap residue, in order to allow the sticky back tape side of door seal to properly stick to the door. There also was a plastic cover over the wire bundle that needed to be cleaned. The inner door seal was the exact length, so proper positioning of the sticky back was very important.
Upon reassemly the leak still existed and I was unable to correct the leak. Further inspection indicated that the basic tub/body of the dishwasher might be slightly distorted due to age and may not create seal with door seal as originally designed.
I guess I need to find a new dishwasher, at this point.
A word to the wise: Check to see if the tub/body is still in good condition.

The Soap Dispenser would not open duirng wash cycle

  • Customer: Roger from Silver Spring MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 44 of 45 people found this instruction helpful
I suspected that the wax motor had gone bad based on reviews I had read. The repair requires a TORX bit to remove seven screws holding the plastic cover on the inside of the door. I sat in a chair with the door resting on my knees and took the screws out. Once open, the two wax motors are under the cover and easily accessible. You simply pull the wax motors out and detach two wire plugs. You should note how the wires are attached. The wire plugs were a little difficult to pull off but with a little effort they came straight off. Once new wax motors were installed, the soap dispenser opened.

I was also using a gel dishwasher detergent and was told that, for some reason, it might have begun to act like glue and this might also have prevented the soap dispenser from opening. I switched to powder and that did not solve the problem leading me to replace the wax motors. The soap dispenser spring seems a little weak so I have continued using powder.

no power

  • Customer: Robert from Johnson VT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 41 of 41 people found this instruction helpful
remove the eight screws that hold the inside door cover to gain access to the door switch.
remove the four wire conections and replace with new new switch
All Instructions for the DW860UQB
1-15 of 520